| 1 | /* |
| 2 | * arch/arm/mach-kirkwood/goflexhome-setup.c |
| 3 | * |
| 4 | * Seagate GoFlex Home Setup |
| 5 | * |
| 6 | * This file is licensed under the terms of the GNU General Public |
| 7 | * License version 2. This program is licensed "as is" without any |
| 8 | * warranty of any kind, whether express or implied. |
| 9 | */ |
| 10 | |
| 11 | #include <linux/kernel.h> |
| 12 | #include <linux/init.h> |
| 13 | #include <linux/platform_device.h> |
| 14 | #include <linux/ata_platform.h> |
| 15 | #include <linux/mtd/partitions.h> |
| 16 | #include <linux/mv643xx_eth.h> |
| 17 | #include <linux/gpio.h> |
| 18 | #include <linux/leds.h> |
| 19 | #include <asm/mach-types.h> |
| 20 | #include <asm/mach/arch.h> |
| 21 | #include <mach/kirkwood.h> |
| 22 | #include "common.h" |
| 23 | #include "mpp.h" |
| 24 | |
| 25 | static struct mtd_partition goflexhome_nand_parts[] = { |
| 26 | { |
| 27 | .name = "u-boot", |
| 28 | .offset = 0, |
| 29 | .size = SZ_1M |
| 30 | }, { |
| 31 | .name = "uImage", |
| 32 | .offset = MTDPART_OFS_NXTBLK, |
| 33 | .size = SZ_2M + SZ_4M |
| 34 | }, { |
| 35 | .name = "root", |
| 36 | .offset = MTDPART_OFS_NXTBLK, |
| 37 | .size = MTDPART_SIZ_FULL |
| 38 | }, |
| 39 | }; |
| 40 | |
| 41 | static struct mv643xx_eth_platform_data goflexhome_ge00_data = { |
| 42 | .phy_addr = MV643XX_ETH_PHY_ADDR(0), |
| 43 | }; |
| 44 | |
| 45 | static struct mv_sata_platform_data goflexhome_sata_data = { |
| 46 | .n_ports = 1, |
| 47 | }; |
| 48 | |
| 49 | static struct gpio_led goflexhome_led_pins[] = { |
| 50 | { |
| 51 | .name = "status:green:health", |
| 52 | .default_trigger = "default-on", |
| 53 | .gpio = 46, |
| 54 | .active_low = 1, |
| 55 | }, |
| 56 | { |
| 57 | .name = "status:orange:fault", |
| 58 | .default_trigger = "none", |
| 59 | .gpio = 47, |
| 60 | .active_low = 1, |
| 61 | }, |
| 62 | { |
| 63 | .name = "status:white:misc", |
| 64 | .default_trigger = "none", |
| 65 | .gpio = 40, |
| 66 | .active_low = 0, |
| 67 | } |
| 68 | }; |
| 69 | |
| 70 | static struct gpio_led_platform_data goflexhome_led_data = { |
| 71 | .leds = goflexhome_led_pins, |
| 72 | .num_leds = ARRAY_SIZE(goflexhome_led_pins), |
| 73 | }; |
| 74 | |
| 75 | static struct platform_device goflexhome_leds = { |
| 76 | .name = "leds-gpio", |
| 77 | .id = -1, |
| 78 | .dev = { |
| 79 | .platform_data = &goflexhome_led_data, |
| 80 | } |
| 81 | }; |
| 82 | |
| 83 | static unsigned int goflexhome_mpp_config[] __initdata = { |
| 84 | MPP29_GPIO, /* USB Power Enable */ |
| 85 | MPP47_GPIO, /* LED Orange */ |
| 86 | MPP46_GPIO, /* LED Green */ |
| 87 | MPP40_GPIO, /* LED White */ |
| 88 | 0 |
| 89 | }; |
| 90 | |
| 91 | static void __init goflexhome_init(void) |
| 92 | { |
| 93 | /* |
| 94 | * Basic setup. Needs to be called early. |
| 95 | */ |
| 96 | kirkwood_init(); |
| 97 | |
| 98 | /* setup gpio pin select */ |
| 99 | kirkwood_mpp_conf(goflexhome_mpp_config); |
| 100 | |
| 101 | kirkwood_uart0_init(); |
| 102 | kirkwood_nand_init(ARRAY_AND_SIZE(goflexhome_nand_parts), 40); |
| 103 | |
| 104 | if (gpio_request(29, "USB Power Enable") != 0 || |
| 105 | gpio_direction_output(29, 1) != 0) |
| 106 | printk(KERN_ERR "can't set up GPIO 29 (USB Power Enable)\n"); |
| 107 | kirkwood_ehci_init(); |
| 108 | kirkwood_ge00_init(&goflexhome_ge00_data); |
| 109 | kirkwood_sata_init(&goflexhome_sata_data); |
| 110 | |
| 111 | platform_device_register(&goflexhome_leds); |
| 112 | } |
| 113 | |
| 114 | MACHINE_START(GOFLEXHOME, "Seagate GoFlex Home") |
| 115 | /* Maintainer: Peter Carmichael <peterjncarm@ovi.com> */ |
| 116 | .atag_offset = 0x100, |
| 117 | .init_machine = goflexhome_init, |
| 118 | .map_io = kirkwood_map_io, |
| 119 | .init_early = kirkwood_init_early, |
| 120 | .init_irq = kirkwood_init_irq, |
| 121 | .timer = &kirkwood_timer, |
| 122 | .restart = kirkwood_restart, |
| 123 | MACHINE_END |
| 124 | |
