| 1 | --- a/arch/mips/bcm63xx/boards/board_bcm963xx.c |
| 2 | +++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c |
| 3 | @@ -432,6 +432,117 @@ static struct board_info __initdata boar |
| 4 | }, |
| 5 | }; |
| 6 | |
| 7 | +static struct board_info __initdata board_gw6200 = { |
| 8 | + .name = "GW6200", |
| 9 | + .expected_cpu_id = 0x6348, |
| 10 | + |
| 11 | + .has_uart0 = 1, |
| 12 | + .has_enet0 = 1, |
| 13 | + .has_enet1 = 1, |
| 14 | + .has_pci = 1, |
| 15 | + |
| 16 | + .enet0 = { |
| 17 | + .has_phy = 1, |
| 18 | + .use_internal_phy = 1, |
| 19 | + }, |
| 20 | + .enet1 = { |
| 21 | + .force_speed_100 = 1, |
| 22 | + .force_duplex_full = 1, |
| 23 | + }, |
| 24 | + |
| 25 | + .has_ohci0 = 1, |
| 26 | + |
| 27 | + .has_dsp = 1, |
| 28 | + .dsp = { |
| 29 | + .gpio_rst = 8, /* FIXME: What is real GPIO here? */ |
| 30 | + .gpio_int = 34, |
| 31 | + .ext_irq = 2, |
| 32 | + .cs = 2, |
| 33 | + }, |
| 34 | + |
| 35 | + .leds = { |
| 36 | + { |
| 37 | + .name = "line1", |
| 38 | + .gpio = 4, |
| 39 | + .active_low = 1, |
| 40 | + }, |
| 41 | + { |
| 42 | + .name = "line2", |
| 43 | + .gpio = 5, |
| 44 | + .active_low = 1, |
| 45 | + }, |
| 46 | + { |
| 47 | + .name = "line3", |
| 48 | + .gpio = 6, |
| 49 | + .active_low = 1, |
| 50 | + }, |
| 51 | + { |
| 52 | + .name = "tel", |
| 53 | + .gpio = 7, |
| 54 | + .active_low = 1, |
| 55 | + }, |
| 56 | + { |
| 57 | + .name = "ethernet", |
| 58 | + .gpio = 35, |
| 59 | + .active_low = 1, |
| 60 | + }, |
| 61 | + }, |
| 62 | + .buttons = { |
| 63 | + { |
| 64 | + .desc = "reset", |
| 65 | + .gpio = 36, |
| 66 | + .active_low = 1, |
| 67 | + .type = EV_KEY, |
| 68 | + .code = KEY_RESTART, |
| 69 | + .threshold = 3, |
| 70 | + }, |
| 71 | + }, |
| 72 | +}; |
| 73 | + |
| 74 | +static struct board_info __initdata board_gw6000 = { |
| 75 | + .name = "GW6000", |
| 76 | + .expected_cpu_id = 0x6348, |
| 77 | + |
| 78 | + .has_uart0 = 1, |
| 79 | + .has_enet0 = 1, |
| 80 | + .has_enet1 = 1, |
| 81 | + .has_pci = 1, |
| 82 | + |
| 83 | + .enet0 = { |
| 84 | + .has_phy = 1, |
| 85 | + .use_internal_phy = 1, |
| 86 | + }, |
| 87 | + .enet1 = { |
| 88 | + .force_speed_100 = 1, |
| 89 | + .force_duplex_full = 1, |
| 90 | + }, |
| 91 | + |
| 92 | + .has_ohci0 = 1, |
| 93 | + |
| 94 | + .has_dsp = 1, |
| 95 | + .dsp = { |
| 96 | + .gpio_rst = 6, |
| 97 | + .gpio_int = 34, |
| 98 | + .ext_irq = 2, |
| 99 | + .cs = 2, |
| 100 | + }, |
| 101 | + |
| 102 | + /* GW6000 has no GPIO-controlled leds */ |
| 103 | + |
| 104 | + .buttons = { |
| 105 | + { |
| 106 | + .desc = "reset", |
| 107 | + .gpio = 36, |
| 108 | + .active_low = 1, |
| 109 | + .type = EV_KEY, |
| 110 | + .code = KEY_RESTART, |
| 111 | + .threshold = 3, |
| 112 | + }, |
| 113 | + }, |
| 114 | +}; |
| 115 | + |
| 116 | + |
| 117 | + |
| 118 | static struct board_info __initdata board_FAST2404 = { |
| 119 | .name = "F@ST2404", |
| 120 | .expected_cpu_id = 0x6348, |
| 121 | @@ -1540,6 +1651,8 @@ static const struct board_info __initdat |
| 122 | #ifdef CONFIG_BCM63XX_CPU_6348 |
| 123 | &board_96348r, |
| 124 | &board_96348gw, |
| 125 | + &board_gw6000, |
| 126 | + &board_gw6200, |
| 127 | &board_96348gw_10, |
| 128 | &board_96348gw_11, |
| 129 | &board_FAST2404, |
| 130 | |
