| 1 | /* |
| 2 | * This program is free software; you can redistribute it and/or modify it |
| 3 | * under the terms of the GNU General Public License version 2 as published |
| 4 | * by the Free Software Foundation. |
| 5 | * |
| 6 | * Copyright (C) 2010 John Crispin <blogic@openwrt.org> |
| 7 | * Copyright (C) 2012 Pieter Voorthuijsen <p.voorthuijsen@gmail.com> |
| 8 | */ |
| 9 | |
| 10 | #include <linux/init.h> |
| 11 | #include <linux/platform_device.h> |
| 12 | #include <linux/mtd/mtd.h> |
| 13 | #include <linux/mtd/partitions.h> |
| 14 | #include <linux/mtd/physmap.h> |
| 15 | #include <linux/input.h> |
| 16 | #include <linux/phy.h> |
| 17 | #include <linux/spi/spi.h> |
| 18 | #include <linux/spi/flash.h> |
| 19 | #include <linux/spi/spi_gpio.h> |
| 20 | #include <linux/ath9k_platform.h> |
| 21 | #include <linux/if_ether.h> |
| 22 | #include <linux/etherdevice.h> |
| 23 | #include <linux/kobject.h> |
| 24 | #include <linux/sysfs.h> |
| 25 | |
| 26 | #include <lantiq_soc.h> |
| 27 | #include <irq.h> |
| 28 | #include <dev-gpio-leds.h> |
| 29 | #include <dev-gpio-buttons.h> |
| 30 | #include "dev-wifi-athxk.h" |
| 31 | |
| 32 | #include "../machtypes.h" |
| 33 | #include "devices.h" |
| 34 | #include "dev-dwc_otg.h" |
| 35 | #include "pci-ath-fixup.h" |
| 36 | #include <mtd/mtd-abi.h> |
| 37 | #include <asm-generic/sizes.h> |
| 38 | |
| 39 | static struct mtd_partition dgn3500_partitions[] = { |
| 40 | { |
| 41 | .name = "u-boot", |
| 42 | .offset = 0, |
| 43 | .size = 0x10000, |
| 44 | .mask_flags = MTD_WRITEABLE, |
| 45 | }, |
| 46 | { |
| 47 | .name = "environment", |
| 48 | .offset = 0x10000, |
| 49 | .size = 0x10000, |
| 50 | .mask_flags = MTD_WRITEABLE, |
| 51 | }, |
| 52 | { |
| 53 | .name = "calibration", |
| 54 | .offset = 0x20000, |
| 55 | .size = 0x10000, |
| 56 | .mask_flags = MTD_WRITEABLE, |
| 57 | }, |
| 58 | { |
| 59 | .name = "linux", |
| 60 | .offset = 0x50000, |
| 61 | .size = 0xfa0000, |
| 62 | }, |
| 63 | }; |
| 64 | |
| 65 | static struct ltq_pci_data ltq_pci_data = { |
| 66 | .clock = PCI_CLOCK_INT, |
| 67 | .gpio = PCI_GNT1 | PCI_REQ1, |
| 68 | .irq = { |
| 69 | [14] = INT_NUM_IM0_IRL0 + 22, |
| 70 | }, |
| 71 | }; |
| 72 | |
| 73 | static struct ltq_eth_data ltq_eth_data = { |
| 74 | .mii_mode = PHY_INTERFACE_MODE_MII, |
| 75 | }; |
| 76 | |
| 77 | static struct gpio_led |
| 78 | dgn3500_gpio_leds[] __initdata = { |
| 79 | { .name = "soc:green:power", .gpio = 34, .active_low = 1, }, |
| 80 | { .name = "soc:red:power", .gpio = 39, .active_low = 1, }, |
| 81 | { .name = "soc:orange:wlan", .gpio = 51, .active_low = 1, }, |
| 82 | { .name = "soc:green:wps", .gpio = 52, .active_low = 1, }, |
| 83 | { .name = "soc:green:usb", .gpio = 22, .active_low = 1, }, |
| 84 | { .name = "soc:green:dsl", .gpio = 4, .active_low = 1, }, |
| 85 | { .name = "soc:green:internet", .gpio = 2, .active_low = 1, }, |
| 86 | }; |
| 87 | |
| 88 | static struct gpio_keys_button |
| 89 | dgn3500_gpio_keys[] __initdata = { |
| 90 | { |
| 91 | .desc = "wps", |
| 92 | .type = EV_KEY, |
| 93 | .code = BTN_0, |
| 94 | .debounce_interval = LTQ_KEYS_DEBOUNCE_INTERVAL, |
| 95 | .gpio = 54, |
| 96 | .active_low = 1, |
| 97 | }, |
| 98 | { |
| 99 | .desc = "reset", |
| 100 | .type = EV_KEY, |
| 101 | .code = BTN_1, |
| 102 | .debounce_interval = LTQ_KEYS_DEBOUNCE_INTERVAL, |
| 103 | .gpio = 36, |
| 104 | .active_low = 1, |
| 105 | }, |
| 106 | }; |
| 107 | |
| 108 | #define SPI_GPIO_MRST 16 |
| 109 | #define SPI_GPIO_MTSR 17 |
| 110 | #define SPI_GPIO_CLK 18 |
| 111 | #define SPI_GPIO_CS0 10 |
| 112 | |
| 113 | static struct spi_gpio_platform_data spi_gpio_data = { |
| 114 | .sck = SPI_GPIO_CLK, |
| 115 | .mosi = SPI_GPIO_MTSR, |
| 116 | .miso = SPI_GPIO_MRST, |
| 117 | .num_chipselect = 2, |
| 118 | }; |
| 119 | |
| 120 | static struct platform_device spi_gpio_device = { |
| 121 | .name = "spi_gpio", |
| 122 | .dev.platform_data = &spi_gpio_data, |
| 123 | }; |
| 124 | |
| 125 | static struct flash_platform_data spi_flash_data = { |
| 126 | .name = "sflash", |
| 127 | .parts = dgn3500_partitions, |
| 128 | .nr_parts = ARRAY_SIZE(dgn3500_partitions), |
| 129 | }; |
| 130 | |
| 131 | static struct spi_board_info spi_flash __initdata = { |
| 132 | .modalias = "m25p80", |
| 133 | .bus_num = 0, |
| 134 | .chip_select = 0, |
| 135 | .max_speed_hz = 10 * 1000 * 1000, |
| 136 | .mode = SPI_MODE_3, |
| 137 | .chip_select = 0, |
| 138 | .controller_data = (void *) SPI_GPIO_CS0, |
| 139 | .platform_data = &spi_flash_data |
| 140 | }; |
| 141 | |
| 142 | static u8 ltq_ethaddr[6] = { 0 }; |
| 143 | |
| 144 | static int __init setup_ethaddr(char *str) |
| 145 | { |
| 146 | if (!mac_pton(str, ltq_ethaddr)) |
| 147 | memset(ltq_ethaddr, 0, 6); |
| 148 | return 0; |
| 149 | } |
| 150 | __setup("ethaddr=", setup_ethaddr); |
| 151 | |
| 152 | static u16 dgn3500_eeprom_data[ATH9K_PLAT_EEP_MAX_WORDS] = {0}; |
| 153 | |
| 154 | static ssize_t ath_eeprom_read(struct file *filp, struct kobject *kobj, |
| 155 | struct bin_attribute *attr, char *buf, |
| 156 | loff_t offset, size_t count) |
| 157 | { |
| 158 | if (unlikely(offset >= sizeof(dgn3500_eeprom_data))) |
| 159 | return 0; |
| 160 | if ((offset + count) > sizeof(dgn3500_eeprom_data)) |
| 161 | count = sizeof(dgn3500_eeprom_data) - offset; |
| 162 | if (unlikely(!count)) |
| 163 | return count; |
| 164 | |
| 165 | memcpy(buf, (char *)(dgn3500_eeprom_data) + offset, count); |
| 166 | |
| 167 | return count; |
| 168 | } |
| 169 | |
| 170 | extern struct ath9k_platform_data ath9k_pdata; |
| 171 | |
| 172 | static ssize_t ath_eeprom_write(struct file *filp, struct kobject *kobj, |
| 173 | struct bin_attribute *attr, char *buf, |
| 174 | loff_t offset, size_t count) |
| 175 | { |
| 176 | int i; |
| 177 | char *eeprom_bytes = (char *)dgn3500_eeprom_data; |
| 178 | |
| 179 | if (unlikely(offset >= sizeof(dgn3500_eeprom_data))) |
| 180 | return -EFBIG; |
| 181 | if ((offset + count) > sizeof(dgn3500_eeprom_data)) |
| 182 | count = sizeof(dgn3500_eeprom_data) - offset; |
| 183 | if (unlikely(!count)) |
| 184 | return count; |
| 185 | if (count % 2) |
| 186 | return 0; |
| 187 | |
| 188 | /* The PCI fixup routine requires an endian swap of the calibartion data |
| 189 | * stored in flash */ |
| 190 | for (i = 0; i < count; i += 2) { |
| 191 | eeprom_bytes[offset + i + 1] = buf[i]; |
| 192 | eeprom_bytes[offset + i] = buf[i+1]; |
| 193 | } |
| 194 | |
| 195 | /* The original data does not contain a checksum. Set the country and |
| 196 | * calculate new checksum when all data is received */ |
| 197 | if ((count + offset) == sizeof(dgn3500_eeprom_data)) |
| 198 | memcpy(ath9k_pdata.eeprom_data, dgn3500_eeprom_data, |
| 199 | sizeof(ath9k_pdata.eeprom_data)); |
| 200 | |
| 201 | return count; |
| 202 | } |
| 203 | |
| 204 | static struct bin_attribute dev_attr_ath_eeprom = { |
| 205 | .attr = { |
| 206 | .name = "ath_eeprom", |
| 207 | .mode = S_IRUGO|S_IWUSR, |
| 208 | }, |
| 209 | .read = ath_eeprom_read, |
| 210 | .write = ath_eeprom_write, |
| 211 | }; |
| 212 | |
| 213 | static void __init dgn3500_init(void) |
| 214 | { |
| 215 | if (sysfs_create_bin_file(firmware_kobj, &dev_attr_ath_eeprom)) |
| 216 | printk(KERN_INFO "Failed to create ath eeprom sysfs entry\n"); |
| 217 | ltq_add_device_gpio_leds(-1, ARRAY_SIZE(dgn3500_gpio_leds), |
| 218 | dgn3500_gpio_leds); |
| 219 | ltq_register_gpio_keys_polled(-1, LTQ_KEYS_POLL_INTERVAL, |
| 220 | ARRAY_SIZE(dgn3500_gpio_keys), dgn3500_gpio_keys); |
| 221 | platform_device_register(&spi_gpio_device); |
| 222 | ltq_register_pci(<q_pci_data); |
| 223 | spi_register_board_info(&spi_flash, 1); |
| 224 | if (!is_valid_ether_addr(ltq_ethaddr)) { |
| 225 | printk(KERN_INFO "MAC invalid using random\n"); |
| 226 | random_ether_addr(ltq_ethaddr); |
| 227 | } |
| 228 | memcpy(<q_eth_data.mac.sa_data, ltq_ethaddr, 6); |
| 229 | ltq_register_etop(<q_eth_data); |
| 230 | ltq_register_ath9k(dgn3500_eeprom_data, ltq_ethaddr); |
| 231 | ltq_pci_ath_fixup(14, dgn3500_eeprom_data); |
| 232 | /* The usb power is always enabled, protected by a fuse */ |
| 233 | xway_register_dwc(-1); |
| 234 | } |
| 235 | |
| 236 | MIPS_MACHINE(LANTIQ_MACH_DGN3500B, |
| 237 | "DGN3500B", |
| 238 | "Netgear DGN3500B", |
| 239 | dgn3500_init); |
| 240 | |