| 1 | --- /dev/null |
| 2 | +++ b/arch/powerpc/boot/cuboot-magicbox.c |
| 3 | @@ -0,0 +1,98 @@ |
| 4 | +/* |
| 5 | + * Old U-boot compatibility for Magicbox boards |
| 6 | + * |
| 7 | + * Author: Imre Kaloz <kaloz@openwrt.org> |
| 8 | + * Gabor Juhos <juhosg@openwrt.org> |
| 9 | + * |
| 10 | + * This program is free software; you can redistribute it and/or modify it |
| 11 | + * under the terms of the GNU General Public License version 2 as published |
| 12 | + * by the Free Software Foundation. |
| 13 | + */ |
| 14 | + |
| 15 | +#include "ops.h" |
| 16 | +#include "io.h" |
| 17 | +#include "dcr.h" |
| 18 | +#include "stdio.h" |
| 19 | +#include "4xx.h" |
| 20 | +#include "44x.h" |
| 21 | +#include "cuboot.h" |
| 22 | + |
| 23 | +#define TARGET_4xx |
| 24 | +#define TARGET_405EP |
| 25 | +#include "ppcboot.h" |
| 26 | + |
| 27 | +static bd_t bd; |
| 28 | + |
| 29 | +static void fixup_perwe(void) |
| 30 | +{ |
| 31 | + |
| 32 | +#define DCRN_CPC0_PCI_BASE 0xf9 |
| 33 | + |
| 34 | + /* Turn on PerWE instead of PCIINT */ |
| 35 | + mtdcr(DCRN_CPC0_PCI_BASE, |
| 36 | + mfdcr(DCRN_CPC0_PCI_BASE) | (0x80000000L >> 27)); |
| 37 | + |
| 38 | +#undef DCRN_CPC0_PCI_BASE |
| 39 | +} |
| 40 | + |
| 41 | +static void fixup_cf_card(void) |
| 42 | +{ |
| 43 | + |
| 44 | +#define CF_CS0_BASE 0xff100000 |
| 45 | +#define CF_CS1_BASE 0xff200000 |
| 46 | + |
| 47 | + /* PerCS1 (CF's CS0): base 0xff100000, 16-bit, rw */ |
| 48 | + mtdcr(DCRN_EBC0_CFGADDR, EBC_B1CR); |
| 49 | + mtdcr(DCRN_EBC0_CFGDATA, CF_CS0_BASE | EBC_BXCR_BS_1M | |
| 50 | + EBC_BXCR_BU_RW | EBC_BXCR_BW_16); |
| 51 | + mtdcr(DCRN_EBC0_CFGADDR, EBC_B1AP); |
| 52 | + mtdcr(DCRN_EBC0_CFGDATA, 0x080bd800); |
| 53 | + |
| 54 | + /* PerCS2 (CF's CS1): base 0xff200000, 16-bit, rw */ |
| 55 | + mtdcr(DCRN_EBC0_CFGADDR, EBC_B2CR); |
| 56 | + mtdcr(DCRN_EBC0_CFGDATA, CF_CS1_BASE | EBC_BXCR_BS_1M | |
| 57 | + EBC_BXCR_BU_RW | EBC_BXCR_BW_16); |
| 58 | + mtdcr(DCRN_EBC0_CFGADDR, EBC_B2AP); |
| 59 | + mtdcr(DCRN_EBC0_CFGDATA, 0x080bd800); |
| 60 | + |
| 61 | +#undef CF_CS0_BASE |
| 62 | +#undef CF_CS1_BASE |
| 63 | +} |
| 64 | + |
| 65 | +static void magicbox_fixups(void) |
| 66 | +{ |
| 67 | + ibm405ep_fixup_clocks(bd.bi_procfreq / 8); |
| 68 | + ibm4xx_sdram_fixup_memsize(); |
| 69 | + |
| 70 | + /* Magicbox v1 has only one ethernet, one serial and no |
| 71 | + * CF slot -- detect it using it's fake enet1addr |
| 72 | + */ |
| 73 | + if ((bd.bi_enet1addr[2] == 0x02) && |
| 74 | + (bd.bi_enet1addr[3] == 0xfa) && |
| 75 | + (bd.bi_enet1addr[4] == 0xf0) && |
| 76 | + (bd.bi_enet1addr[5] == 0x80)) { |
| 77 | + void *devp; |
| 78 | + devp = finddevice("/plb/opb/ethernet@ef600900"); |
| 79 | + del_node(devp); |
| 80 | + devp = finddevice("/plb/opb/serial@ef600400"); |
| 81 | + del_node(devp); |
| 82 | + devp = finddevice("/plb/ebc/cf_card@ff100000"); |
| 83 | + del_node(devp); |
| 84 | + |
| 85 | + } else { |
| 86 | + fixup_perwe(); |
| 87 | + fixup_cf_card(); |
| 88 | + } |
| 89 | + |
| 90 | + dt_fixup_mac_addresses(&bd.bi_enetaddr, &bd.bi_enet1addr); |
| 91 | +} |
| 92 | + |
| 93 | +void platform_init(unsigned long r3, unsigned long r4, unsigned long r5, |
| 94 | + unsigned long r6, unsigned long r7) |
| 95 | +{ |
| 96 | + CUBOOT_INIT(); |
| 97 | + platform_ops.fixups = magicbox_fixups; |
| 98 | + platform_ops.exit = ibm40x_dbcr_reset; |
| 99 | + fdt_init(_dtb_start); |
| 100 | + serial_console_init(); |
| 101 | +} |
| 102 | --- /dev/null |
| 103 | +++ b/arch/powerpc/boot/dts/magicbox.dts |
| 104 | @@ -0,0 +1,285 @@ |
| 105 | +/* |
| 106 | + * Device Tree Source for Magicbox boards |
| 107 | + * |
| 108 | + * Copyright 2008-2009 Imre Kaloz <kaloz@openwrt.org> |
| 109 | + * Copyright 2009 Gabor Juhos <juhosg@openwrt.org> |
| 110 | + * |
| 111 | + * Based on walnut.dts |
| 112 | + * |
| 113 | + * This file is licensed under the terms of the GNU General Public |
| 114 | + * License version 2. This program is licensed "as is" without |
| 115 | + * any warranty of any kind, whether express or implied. |
| 116 | + */ |
| 117 | + |
| 118 | +/dts-v1/; |
| 119 | + |
| 120 | +/ { |
| 121 | + #address-cells = <1>; |
| 122 | + #size-cells = <1>; |
| 123 | + model = "magicbox"; |
| 124 | + compatible = "magicbox"; |
| 125 | + dcr-parent = <&{/cpus/cpu@0}>; |
| 126 | + |
| 127 | + aliases { |
| 128 | + ethernet0 = &EMAC0; |
| 129 | + ethernet1 = &EMAC1; |
| 130 | + serial0 = &UART0; |
| 131 | + serial1 = &UART1; |
| 132 | + }; |
| 133 | + |
| 134 | + cpus { |
| 135 | + #address-cells = <1>; |
| 136 | + #size-cells = <0>; |
| 137 | + |
| 138 | + cpu@0 { |
| 139 | + device_type = "cpu"; |
| 140 | + model = "PowerPC,405EP"; |
| 141 | + reg = <0x00000000>; |
| 142 | + clock-frequency = <0>; /* Filled in by zImage */ |
| 143 | + timebase-frequency = <0>; /* Filled in by zImage */ |
| 144 | + i-cache-line-size = <0x20>; |
| 145 | + d-cache-line-size = <0x20>; |
| 146 | + i-cache-size = <0x4000>; |
| 147 | + d-cache-size = <0x4000>; |
| 148 | + dcr-controller; |
| 149 | + dcr-access-method = "native"; |
| 150 | + }; |
| 151 | + }; |
| 152 | + |
| 153 | + memory { |
| 154 | + device_type = "memory"; |
| 155 | + reg = <0x00000000 0x00000000>; /* Filled in by zImage */ |
| 156 | + }; |
| 157 | + |
| 158 | + UIC0: interrupt-controller { |
| 159 | + compatible = "ibm,uic"; |
| 160 | + interrupt-controller; |
| 161 | + cell-index = <0>; |
| 162 | + dcr-reg = <0x0c0 0x009>; |
| 163 | + #address-cells = <0>; |
| 164 | + #size-cells = <0>; |
| 165 | + #interrupt-cells = <2>; |
| 166 | + }; |
| 167 | + |
| 168 | + plb { |
| 169 | + compatible = "ibm,plb3"; |
| 170 | + #address-cells = <1>; |
| 171 | + #size-cells = <1>; |
| 172 | + ranges; |
| 173 | + clock-frequency = <0>; /* Filled in by zImage */ |
| 174 | + |
| 175 | + SDRAM0: memory-controller { |
| 176 | + compatible = "ibm,sdram-405ep"; |
| 177 | + dcr-reg = <0x010 0x002>; |
| 178 | + }; |
| 179 | + |
| 180 | + MAL: mcmal { |
| 181 | + compatible = "ibm,mcmal-405ep", "ibm,mcmal"; |
| 182 | + dcr-reg = <0x180 0x062>; |
| 183 | + num-tx-chans = <4>; |
| 184 | + num-rx-chans = <2>; |
| 185 | + interrupt-parent = <&UIC0>; |
| 186 | + interrupts = < |
| 187 | + 0xb 0x4 /* TXEOB */ |
| 188 | + 0xc 0x4 /* RXEOB */ |
| 189 | + 0xa 0x4 /* SERR */ |
| 190 | + 0xd 0x4 /* TXDE */ |
| 191 | + 0xe 0x4 /* RXDE */>; |
| 192 | + }; |
| 193 | + |
| 194 | + POB0: opb { |
| 195 | + compatible = "ibm,opb-405ep", "ibm,opb"; |
| 196 | + #address-cells = <1>; |
| 197 | + #size-cells = <1>; |
| 198 | + ranges = <0xef600000 0xef600000 0x00a00000>; |
| 199 | + dcr-reg = <0x0a0 0x005>; |
| 200 | + clock-frequency = <0>; /* Filled in by zImage */ |
| 201 | + |
| 202 | + UART0: serial@ef600300 { |
| 203 | + device_type = "serial"; |
| 204 | + compatible = "ns16550"; |
| 205 | + reg = <0xef600300 0x00000008>; |
| 206 | + virtual-reg = <0xef600300>; |
| 207 | + clock-frequency = <0>; /* Filled in by zImage */ |
| 208 | + current-speed = <115200>; |
| 209 | + interrupt-parent = <&UIC0>; |
| 210 | + interrupts = <0x0 0x4>; |
| 211 | + }; |
| 212 | + |
| 213 | + UART1: serial@ef600400 { |
| 214 | + device_type = "serial"; |
| 215 | + compatible = "ns16550"; |
| 216 | + reg = <0xef600400 0x00000008>; |
| 217 | + virtual-reg = <0xef600400>; |
| 218 | + clock-frequency = <0>; /* Filled in by zImage */ |
| 219 | + current-speed = <115200>; |
| 220 | + interrupt-parent = <&UIC0>; |
| 221 | + interrupts = <0x1 0x4>; |
| 222 | + }; |
| 223 | + |
| 224 | + IIC: i2c@ef600500 { |
| 225 | + compatible = "ibm,iic-405ep", "ibm,iic"; |
| 226 | + #address-cells = <1>; |
| 227 | + #size-cells = <0>; |
| 228 | + reg = <0xef600500 0x00000011>; |
| 229 | + interrupt-parent = <&UIC0>; |
| 230 | + interrupts = <0x2 0x4>; |
| 231 | + |
| 232 | + dtt@48 { |
| 233 | + compatible = "national,lm75"; |
| 234 | + reg = <0x48>; |
| 235 | + }; |
| 236 | + |
| 237 | + eeprom@50 { |
| 238 | + compatible = "at24,24c16"; |
| 239 | + reg = <0x50>; |
| 240 | + }; |
| 241 | + }; |
| 242 | + |
| 243 | + GPIO0: gpio-controller@ef600700 { |
| 244 | + compatible = "ibm,ppc4xx-gpio"; |
| 245 | + reg = <0xef600700 0x00000020>; |
| 246 | + #gpio-cells = <2>; |
| 247 | + gpio-controller; |
| 248 | + }; |
| 249 | + |
| 250 | + EMAC0: ethernet@ef600800 { |
| 251 | + linux,network-index = <0x0>; |
| 252 | + device_type = "network"; |
| 253 | + compatible = "ibm,emac-405ep", "ibm,emac"; |
| 254 | + interrupt-parent = <&UIC0>; |
| 255 | + interrupts = < |
| 256 | + 0xf 0x4 /* Ethernet */ |
| 257 | + 0x9 0x4 /* Ethernet Wake Up */>; |
| 258 | + local-mac-address = [000000000000]; /* Filled in by zImage */ |
| 259 | + reg = <0xef600800 0x00000070>; |
| 260 | + mal-device = <&MAL>; |
| 261 | + mal-tx-channel = <0>; |
| 262 | + mal-rx-channel = <0>; |
| 263 | + cell-index = <0>; |
| 264 | + max-frame-size = <0x5dc>; |
| 265 | + rx-fifo-size = <0x1000>; |
| 266 | + tx-fifo-size = <0x800>; |
| 267 | + phy-mode = "mii"; |
| 268 | + phy-map = <0x00000000>; |
| 269 | + }; |
| 270 | + |
| 271 | + EMAC1: ethernet@ef600900 { |
| 272 | + linux,network-index = <0x1>; |
| 273 | + device_type = "network"; |
| 274 | + compatible = "ibm,emac-405ep", "ibm,emac"; |
| 275 | + interrupt-parent = <&UIC0>; |
| 276 | + interrupts = < |
| 277 | + 0x11 0x4 /* Ethernet */ |
| 278 | + 0x09 0x4 /* Ethernet Wake Up */>; |
| 279 | + local-mac-address = [000000000000]; /* Filled in by zImage */ |
| 280 | + reg = <0xef600900 0x00000070>; |
| 281 | + mal-device = <&MAL>; |
| 282 | + mal-tx-channel = <2>; |
| 283 | + mal-rx-channel = <1>; |
| 284 | + cell-index = <1>; |
| 285 | + max-frame-size = <0x5dc>; |
| 286 | + rx-fifo-size = <0x1000>; |
| 287 | + tx-fifo-size = <0x800>; |
| 288 | + mdio-device = <&EMAC0>; |
| 289 | + phy-mode = "mii"; |
| 290 | + phy-map = <0x00000001>; |
| 291 | + }; |
| 292 | + |
| 293 | + leds { |
| 294 | + compatible = "gpio-leds"; |
| 295 | + user { |
| 296 | + label = "magicbox:red:user"; |
| 297 | + gpios = <&GPIO0 2 1>; |
| 298 | + }; |
| 299 | + }; |
| 300 | + }; |
| 301 | + |
| 302 | + EBC0: ebc { |
| 303 | + compatible = "ibm,ebc-405ep", "ibm,ebc"; |
| 304 | + dcr-reg = <0x012 0x002>; |
| 305 | + #address-cells = <2>; |
| 306 | + #size-cells = <1>; |
| 307 | + /* The ranges property is supplied by the bootwrapper |
| 308 | + * and is based on the firmware's configuration of the |
| 309 | + * EBC bridge |
| 310 | + */ |
| 311 | + clock-frequency = <0>; /* Filled in by zImage */ |
| 312 | + |
| 313 | + cf_card@ff100000 { |
| 314 | + compatible = "magicbox-cf", "pata-magicbox-cf"; |
| 315 | + reg = <0x00000000 0xff100000 0x00001000 |
| 316 | + 0x00000000 0xff200000 0x00001000>; |
| 317 | + interrupt-parent = <&UIC0>; |
| 318 | + interrupts = <0x19 0x1 /* IRQ_TYPE_EDGE_RISING */ >; |
| 319 | + }; |
| 320 | + |
| 321 | + nor_flash@ffc00000 { |
| 322 | + compatible = "cfi-flash"; |
| 323 | + bank-width = <2>; |
| 324 | + reg = <0x00000000 0xffc00000 0x00400000>; |
| 325 | + #address-cells = <1>; |
| 326 | + #size-cells = <1>; |
| 327 | + partition0@0 { |
| 328 | + label = "linux"; |
| 329 | + reg = <0x0 0x140000>; |
| 330 | + }; |
| 331 | + partition1@120000 { |
| 332 | + label = "rootfs"; |
| 333 | + reg = <0x140000 0x280000>; |
| 334 | + }; |
| 335 | + partition2@3c0000 { |
| 336 | + label = "u-boot"; |
| 337 | + reg = <0x3c0000 0x30000>; |
| 338 | + read-only; |
| 339 | + }; |
| 340 | + partition3@0 { |
| 341 | + label = "firmware"; |
| 342 | + reg = <0x0 0x3c0000>; |
| 343 | + }; |
| 344 | + }; |
| 345 | + }; |
| 346 | + |
| 347 | + PCI0: pci@ec000000 { |
| 348 | + device_type = "pci"; |
| 349 | + #interrupt-cells = <1>; |
| 350 | + #size-cells = <2>; |
| 351 | + #address-cells = <3>; |
| 352 | + compatible = "ibm,plb405ep-pci", "ibm,plb-pci"; |
| 353 | + primary; |
| 354 | + reg = <0xeec00000 0x00000008 /* Config space access */ |
| 355 | + 0xeed80000 0x00000004 /* IACK */ |
| 356 | + 0xeed80000 0x00000004 /* Special cycle */ |
| 357 | + 0xef480000 0x00000040>; /* Internal registers */ |
| 358 | + |
| 359 | + /* Outbound ranges, one memory and one IO, |
| 360 | + * later cannot be changed. Chip supports a second |
| 361 | + * IO range but we don't use it for now |
| 362 | + */ |
| 363 | + ranges = <0x02000000 0x00000000 0x80000000 0x80000000 0x00000000 0x20000000 |
| 364 | + 0x01000000 0x00000000 0x00000000 0xe8000000 0x00000000 0x00010000>; |
| 365 | + |
| 366 | + /* Inbound 2GB range starting at 0 */ |
| 367 | + dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x80000000>; |
| 368 | + |
| 369 | + interrupt-map-mask = <0xf800 0x0 0x0 0x0>; |
| 370 | + interrupt-map = < |
| 371 | + /* IDSEL 1 */ |
| 372 | + 0x800 0x0 0x0 0x0 &UIC0 0x1c 0x8 |
| 373 | + |
| 374 | + /* IDSEL 2 */ |
| 375 | + 0x1000 0x0 0x0 0x0 &UIC0 0x1d 0x8 |
| 376 | + |
| 377 | + /* IDSEL 3 */ |
| 378 | + 0x1800 0x0 0x0 0x0 &UIC0 0x1e 0x8 |
| 379 | + |
| 380 | + /* IDSEL 4 */ |
| 381 | + 0x2000 0x0 0x0 0x0 &UIC0 0x1f 0x8 |
| 382 | + >; |
| 383 | + }; |
| 384 | + }; |
| 385 | + |
| 386 | + chosen { |
| 387 | + linux,stdout-path = "/plb/opb/serial@ef600300"; |
| 388 | + }; |
| 389 | +}; |
| 390 | --- a/arch/powerpc/boot/Makefile |
| 391 | +++ b/arch/powerpc/boot/Makefile |
| 392 | @@ -43,6 +43,7 @@ $(obj)/cuboot-hotfoot.o: BOOTCFLAGS += - |
| 393 | $(obj)/cuboot-taishan.o: BOOTCFLAGS += -mcpu=440 |
| 394 | $(obj)/cuboot-katmai.o: BOOTCFLAGS += -mcpu=440 |
| 395 | $(obj)/cuboot-acadia.o: BOOTCFLAGS += -mcpu=405 |
| 396 | +$(obj)/cuboot-magicbox.o: BOOTCFLAGS += -mcpu=405 |
| 397 | $(obj)/treeboot-walnut.o: BOOTCFLAGS += -mcpu=405 |
| 398 | $(obj)/treeboot-iss4xx.o: BOOTCFLAGS += -mcpu=405 |
| 399 | $(obj)/treeboot-currituck.o: BOOTCFLAGS += -mcpu=405 |
| 400 | @@ -81,7 +82,7 @@ src-plat := of.c cuboot-52xx.c cuboot-82 |
| 401 | virtex405-head.S virtex.c redboot-83xx.c cuboot-sam440ep.c \ |
| 402 | cuboot-acadia.c cuboot-amigaone.c cuboot-kilauea.c \ |
| 403 | gamecube-head.S gamecube.c wii-head.S wii.c treeboot-iss4xx.c \ |
| 404 | - treeboot-currituck.c |
| 405 | + treeboot-currituck.c cuboot-magicbox.c |
| 406 | src-boot := $(src-wlib) $(src-plat) empty.c |
| 407 | |
| 408 | src-boot := $(addprefix $(obj)/, $(src-boot)) |
| 409 | @@ -202,6 +203,7 @@ image-$(CONFIG_HOTFOOT) += cuImage.hot |
| 410 | image-$(CONFIG_WALNUT) += treeImage.walnut |
| 411 | image-$(CONFIG_ACADIA) += cuImage.acadia |
| 412 | image-$(CONFIG_OBS600) += uImage.obs600 |
| 413 | +image-$(CONFIG_MAGICBOX) += cuImage.magicbox |
| 414 | |
| 415 | # Board ports in arch/powerpc/platform/44x/Kconfig |
| 416 | image-$(CONFIG_EBONY) += treeImage.ebony cuImage.ebony |
| 417 | --- a/arch/powerpc/platforms/40x/Kconfig |
| 418 | +++ b/arch/powerpc/platforms/40x/Kconfig |
| 419 | @@ -38,6 +38,16 @@ config KILAUEA |
| 420 | help |
| 421 | This option enables support for the AMCC PPC405EX evaluation board. |
| 422 | |
| 423 | +config MAGICBOX |
| 424 | + bool "Magicbox" |
| 425 | + depends on 40x |
| 426 | + default n |
| 427 | + select PPC40x_SIMPLE |
| 428 | + select 405EP |
| 429 | + select PCI |
| 430 | + help |
| 431 | + This option enables support for the Magicbox boards. |
| 432 | + |
| 433 | config MAKALU |
| 434 | bool "Makalu" |
| 435 | depends on 40x |
| 436 | --- a/arch/powerpc/platforms/40x/ppc40x_simple.c |
| 437 | +++ b/arch/powerpc/platforms/40x/ppc40x_simple.c |
| 438 | @@ -57,6 +57,7 @@ static const char *board[] __initdata = |
| 439 | "amcc,makalu", |
| 440 | "apm,klondike", |
| 441 | "est,hotfoot", |
| 442 | + "magicbox", |
| 443 | "plathome,obs600" |
| 444 | }; |
| 445 | |
| 446 | |
