Age Message
10 years 2 months dma: jz4740: Dequeue descriptor from active list before completing it

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
10 years 3 months mips: qi_lb60: update defconfig for the Ben NanoNote

Update defconfig for the Ben NanoNote to make use of the new musb glue
layer for the JZ4740 USB device controller instead of the original USB
gadget driver.

Signed-off-by: Apelete Seketeli <apelete@seketeli.net>
10 years 9 months usb: musb: add support for JZ4740 usb device controller

Add support for Ingenic JZ4740 USB Device Controller through a
specific musb glue layer.

The platform data already available in tree for that USB Device
Controller was previously used by an out-of-tree USB gadget driver
which was not relying on the musb driver and was written by Ingenic
and the Qi-Hardware community.

JZ4740 UDC not being OTG compatible and missing some hardware
registers, this musb glue layer is written from scratch to be used in
gadget mode only and take silicon design specifics into account.

Signed-off-by: Apelete Seketeli <apelete@seketeli.net>
10 years 3 months usb: musb_gadget: use is_otg flag to set gadget peripheral mode on reset

Since jz4740 is not OTG compatible, rely on is_otg flag to set gadget
peripheral mode on reset instead of accessing devct register which
does not exists.

Signed-off-by: Apelete Seketeli <apelete@seketeli.net>
10 years 3 months usb: musb: fix setting JZ4740 gadget periphal mode on reset

JZ4740 USB Device Controller is not OTG compatible and does not have DEVCTL
register in silicon.

During ethernet-over-usb transactions, on reset, musb driver tries to
read from DEVCTL and consequently sets device as host (A-Device)
instead of peripheral (B-Device), which makes it a composite device to
the USB gadget driver.
This induces a kernel panic during power down where the USB gadget
driver does a null pointer dereference when trying to access the
composite device configuration.

On reset, do not rely on DEVCTL value for setting gadget peripheral
mode: hardcode it instead to B-Device.

Signed-off-by: Apelete Seketeli <apelete@seketeli.net>
10 years 10 months slcd: Use generic dmaengine interface
10 years 10 months ASoC: jz4740: Use the generic dmaengine PCM driver

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
10 years 10 months mmc: jz4740: Add devicetree support

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
10 years 10 months mmc: jz4740: Use a regulator for power control
10 years 10 months ASoC: jz4740-codec: Add device tree support

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
10 years 10 months drivers/rtc/rtc-jz4740.c: jz4740: Add device tree support

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
10 years 10 months drivers/rtc/rtc-jz4740.c: Use managed resources

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
10 years 10 months mmc: jz4740: Use clk_prepare_enable/clk_disable_unprepare

In preparation to switching the jz4740 clk driver to the common clk framework
update the clk enable/disable calls to clk_prepare_enable/clk_disable_unprepare.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
10 years 10 months pwm: jz4740: Pass device to clk_get

In preparation to switching the jz4740 clk driver to the common clk framework
make sure to pass the device to clk_get().

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
13 years 6 months Add defconfig for the Dingoo A320

This is the config from the jz-3.5 branch brought up to date for 3.6.
13 years 4 months Add defconfig for the Ben NanoNote

This is the config from the jz-3.5 branch brought up to date for 3.6.
12 years 9 months OpenDingux: Add initrd

The initrd contents are specified using initrd/tree.txt. The gen_init_cpio
tool will parse that text file and generate a cpio archive.

splashkill is a simple program that is meant to be launched directly by the
kernel, before mininit. It forks itself and sleeps until the ENTER key is
pressed; when it occurs, it enables the framebuffer console by writting to
a file in /sys. This permits to 'kill' the kernel splash screen, in order
to display the boot log.

The source for the mininit and splashkill binaries can be found here:
https://github.com/Ayla-/mininit
12 years 1 month OpenDingux: Add logo

We have a full-screen logo that is used as a splash screen.
13 years 3 days MIPS: A320: Add Dingoo A320 board support

This is a squashed version of the development done in the jz-3.5 branch.
12 years 7 months MIPS: A320: Add SoC sound support for Dingoo A320
11 years 9 months MIPS: JZ4740: Work around fbcon logo crash with SLCD

The logo data is in the init section. However, when using the SLCD driver,
the fbcon code will try to fetch the logo data after the init section has
already been freed, potentially crashing the kernel.

This is a workaround because we have to release a stable kernel now.
The root cause should be found and fixed later.
12 years 9 months MIPS: JZ4740: SLCD framebufer driver

This driver sends the frame buffer to a smart LCD controller,
that is a controller with its own video memory.
It is a squashed version of development done in the jz-3.5 branch.
12 years 8 months MMC: JZ4740: Added support for CPU frequency changing

The MSC device clock is stopped before the frequency change.
After the change a new divider is computed and the clock is restarted.
Also the frequency change is postponed if an I/O operation is in progress.
13 years 3 days MIPS: JZ4740: Add cpufreq support

This is a squashed version of Uli's driver that was further developed
in the qi-kernel repository.
13 years 6 months MIPS: JZ4740: Added setting of PLL rate and main dividers

This functionality makes a cpufreq driver possible.
Squashed version of the development done in the jz-2.6.39 branch.


interactive