Root/
1 | /* |
2 | * eth1394.c -- IPv4 driver for Linux IEEE-1394 Subsystem |
3 | * |
4 | * Copyright (C) 2001-2003 Ben Collins <bcollins@debian.org> |
5 | * 2000 Bonin Franck <boninf@free.fr> |
6 | * 2003 Steve Kinneberg <kinnebergsteve@acmsystems.com> |
7 | * |
8 | * Mainly based on work by Emanuel Pirker and Andreas E. Bombe |
9 | * |
10 | * This program is free software; you can redistribute it and/or modify |
11 | * it under the terms of the GNU General Public License as published by |
12 | * the Free Software Foundation; either version 2 of the License, or |
13 | * (at your option) any later version. |
14 | * |
15 | * This program is distributed in the hope that it will be useful, |
16 | * but WITHOUT ANY WARRANTY; without even the implied warranty of |
17 | * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
18 | * GNU General Public License for more details. |
19 | * |
20 | * You should have received a copy of the GNU General Public License |
21 | * along with this program; if not, write to the Free Software Foundation, |
22 | * Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. |
23 | */ |
24 | |
25 | /* |
26 | * This driver intends to support RFC 2734, which describes a method for |
27 | * transporting IPv4 datagrams over IEEE-1394 serial busses. |
28 | * |
29 | * TODO: |
30 | * RFC 2734 related: |
31 | * - Add MCAP. Limited Multicast exists only to 224.0.0.1 and 224.0.0.2. |
32 | * |
33 | * Non-RFC 2734 related: |
34 | * - Handle fragmented skb's coming from the networking layer. |
35 | * - Move generic GASP reception to core 1394 code |
36 | * - Convert kmalloc/kfree for link fragments to use kmem_cache_* instead |
37 | * - Stability improvements |
38 | * - Performance enhancements |
39 | * - Consider garbage collecting old partial datagrams after X amount of time |
40 | */ |
41 | |
42 | #include <linux/module.h> |
43 | |
44 | #include <linux/kernel.h> |
45 | #include <linux/slab.h> |
46 | #include <linux/errno.h> |
47 | #include <linux/types.h> |
48 | #include <linux/delay.h> |
49 | #include <linux/init.h> |
50 | #include <linux/workqueue.h> |
51 | |
52 | #include <linux/netdevice.h> |
53 | #include <linux/inetdevice.h> |
54 | #include <linux/if_arp.h> |
55 | #include <linux/if_ether.h> |
56 | #include <linux/ip.h> |
57 | #include <linux/in.h> |
58 | #include <linux/tcp.h> |
59 | #include <linux/skbuff.h> |
60 | #include <linux/bitops.h> |
61 | #include <linux/ethtool.h> |
62 | #include <asm/uaccess.h> |
63 | #include <asm/delay.h> |
64 | #include <asm/unaligned.h> |
65 | #include <net/arp.h> |
66 | |
67 | #include "config_roms.h" |
68 | #include "csr1212.h" |
69 | #include "eth1394.h" |
70 | #include "highlevel.h" |
71 | #include "ieee1394.h" |
72 | #include "ieee1394_core.h" |
73 | #include "ieee1394_hotplug.h" |
74 | #include "ieee1394_transactions.h" |
75 | #include "ieee1394_types.h" |
76 | #include "iso.h" |
77 | #include "nodemgr.h" |
78 | |
79 | #define ETH1394_PRINT_G(level, fmt, args...) \ |
80 | printk(level "%s: " fmt, driver_name, ## args) |
81 | |
82 | #define ETH1394_PRINT(level, dev_name, fmt, args...) \ |
83 | printk(level "%s: %s: " fmt, driver_name, dev_name, ## args) |
84 | |
85 | struct fragment_info { |
86 | struct list_head list; |
87 | int offset; |
88 | int len; |
89 | }; |
90 | |
91 | struct partial_datagram { |
92 | struct list_head list; |
93 | u16 dgl; |
94 | u16 dg_size; |
95 | __be16 ether_type; |
96 | struct sk_buff *skb; |
97 | char *pbuf; |
98 | struct list_head frag_info; |
99 | }; |
100 | |
101 | struct pdg_list { |
102 | struct list_head list; /* partial datagram list per node */ |
103 | unsigned int sz; /* partial datagram list size per node */ |
104 | spinlock_t lock; /* partial datagram lock */ |
105 | }; |
106 | |
107 | struct eth1394_host_info { |
108 | struct hpsb_host *host; |
109 | struct net_device *dev; |
110 | }; |
111 | |
112 | struct eth1394_node_ref { |
113 | struct unit_directory *ud; |
114 | struct list_head list; |
115 | }; |
116 | |
117 | struct eth1394_node_info { |
118 | u16 maxpayload; /* max payload */ |
119 | u8 sspd; /* max speed */ |
120 | u64 fifo; /* FIFO address */ |
121 | struct pdg_list pdg; /* partial RX datagram lists */ |
122 | int dgl; /* outgoing datagram label */ |
123 | }; |
124 | |
125 | static const char driver_name[] = "eth1394"; |
126 | |
127 | static struct kmem_cache *packet_task_cache; |
128 | |
129 | static struct hpsb_highlevel eth1394_highlevel; |
130 | |
131 | /* Use common.lf to determine header len */ |
132 | static const int hdr_type_len[] = { |
133 | sizeof(struct eth1394_uf_hdr), |
134 | sizeof(struct eth1394_ff_hdr), |
135 | sizeof(struct eth1394_sf_hdr), |
136 | sizeof(struct eth1394_sf_hdr) |
137 | }; |
138 | |
139 | static const u16 eth1394_speedto_maxpayload[] = { |
140 | /* S100, S200, S400, S800, S1600, S3200 */ |
141 | 512, 1024, 2048, 4096, 4096, 4096 |
142 | }; |
143 | |
144 | MODULE_AUTHOR("Ben Collins (bcollins@debian.org)"); |
145 | MODULE_DESCRIPTION("IEEE 1394 IPv4 Driver (IPv4-over-1394 as per RFC 2734)"); |
146 | MODULE_LICENSE("GPL"); |
147 | |
148 | /* |
149 | * The max_partial_datagrams parameter is the maximum number of fragmented |
150 | * datagrams per node that eth1394 will keep in memory. Providing an upper |
151 | * bound allows us to limit the amount of memory that partial datagrams |
152 | * consume in the event that some partial datagrams are never completed. |
153 | */ |
154 | static int max_partial_datagrams = 25; |
155 | module_param(max_partial_datagrams, int, S_IRUGO | S_IWUSR); |
156 | MODULE_PARM_DESC(max_partial_datagrams, |
157 | "Maximum number of partially received fragmented datagrams " |
158 | "(default = 25)."); |
159 | |
160 | |
161 | static int ether1394_header(struct sk_buff *skb, struct net_device *dev, |
162 | unsigned short type, const void *daddr, |
163 | const void *saddr, unsigned len); |
164 | static int ether1394_rebuild_header(struct sk_buff *skb); |
165 | static int ether1394_header_parse(const struct sk_buff *skb, |
166 | unsigned char *haddr); |
167 | static int ether1394_header_cache(const struct neighbour *neigh, |
168 | struct hh_cache *hh); |
169 | static void ether1394_header_cache_update(struct hh_cache *hh, |
170 | const struct net_device *dev, |
171 | const unsigned char *haddr); |
172 | static netdev_tx_t ether1394_tx(struct sk_buff *skb, |
173 | struct net_device *dev); |
174 | static void ether1394_iso(struct hpsb_iso *iso); |
175 | |
176 | static const struct ethtool_ops ethtool_ops; |
177 | |
178 | static int ether1394_write(struct hpsb_host *host, int srcid, int destid, |
179 | quadlet_t *data, u64 addr, size_t len, u16 flags); |
180 | static void ether1394_add_host(struct hpsb_host *host); |
181 | static void ether1394_remove_host(struct hpsb_host *host); |
182 | static void ether1394_host_reset(struct hpsb_host *host); |
183 | |
184 | /* Function for incoming 1394 packets */ |
185 | static const struct hpsb_address_ops addr_ops = { |
186 | .write = ether1394_write, |
187 | }; |
188 | |
189 | /* Ieee1394 highlevel driver functions */ |
190 | static struct hpsb_highlevel eth1394_highlevel = { |
191 | .name = driver_name, |
192 | .add_host = ether1394_add_host, |
193 | .remove_host = ether1394_remove_host, |
194 | .host_reset = ether1394_host_reset, |
195 | }; |
196 | |
197 | static int ether1394_recv_init(struct eth1394_priv *priv) |
198 | { |
199 | unsigned int iso_buf_size; |
200 | |
201 | /* FIXME: rawiso limits us to PAGE_SIZE */ |
202 | iso_buf_size = min((unsigned int)PAGE_SIZE, |
203 | 2 * (1U << (priv->host->csr.max_rec + 1))); |
204 | |
205 | priv->iso = hpsb_iso_recv_init(priv->host, |
206 | ETHER1394_GASP_BUFFERS * iso_buf_size, |
207 | ETHER1394_GASP_BUFFERS, |
208 | priv->broadcast_channel, |
209 | HPSB_ISO_DMA_PACKET_PER_BUFFER, |
210 | 1, ether1394_iso); |
211 | if (priv->iso == NULL) { |
212 | ETH1394_PRINT_G(KERN_ERR, "Failed to allocate IR context\n"); |
213 | priv->bc_state = ETHER1394_BC_ERROR; |
214 | return -EAGAIN; |
215 | } |
216 | |
217 | if (hpsb_iso_recv_start(priv->iso, -1, (1 << 3), -1) < 0) |
218 | priv->bc_state = ETHER1394_BC_STOPPED; |
219 | else |
220 | priv->bc_state = ETHER1394_BC_RUNNING; |
221 | return 0; |
222 | } |
223 | |
224 | /* This is called after an "ifup" */ |
225 | static int ether1394_open(struct net_device *dev) |
226 | { |
227 | struct eth1394_priv *priv = netdev_priv(dev); |
228 | int ret; |
229 | |
230 | if (priv->bc_state == ETHER1394_BC_ERROR) { |
231 | ret = ether1394_recv_init(priv); |
232 | if (ret) |
233 | return ret; |
234 | } |
235 | netif_start_queue(dev); |
236 | return 0; |
237 | } |
238 | |
239 | /* This is called after an "ifdown" */ |
240 | static int ether1394_stop(struct net_device *dev) |
241 | { |
242 | /* flush priv->wake */ |
243 | flush_scheduled_work(); |
244 | |
245 | netif_stop_queue(dev); |
246 | return 0; |
247 | } |
248 | |
249 | /* FIXME: What to do if we timeout? I think a host reset is probably in order, |
250 | * so that's what we do. Should we increment the stat counters too? */ |
251 | static void ether1394_tx_timeout(struct net_device *dev) |
252 | { |
253 | struct hpsb_host *host = |
254 | ((struct eth1394_priv *)netdev_priv(dev))->host; |
255 | |
256 | ETH1394_PRINT(KERN_ERR, dev->name, "Timeout, resetting host\n"); |
257 | ether1394_host_reset(host); |
258 | } |
259 | |
260 | static inline int ether1394_max_mtu(struct hpsb_host* host) |
261 | { |
262 | return (1 << (host->csr.max_rec + 1)) |
263 | - sizeof(union eth1394_hdr) - ETHER1394_GASP_OVERHEAD; |
264 | } |
265 | |
266 | static int ether1394_change_mtu(struct net_device *dev, int new_mtu) |
267 | { |
268 | int max_mtu; |
269 | |
270 | if (new_mtu < 68) |
271 | return -EINVAL; |
272 | |
273 | max_mtu = ether1394_max_mtu( |
274 | ((struct eth1394_priv *)netdev_priv(dev))->host); |
275 | if (new_mtu > max_mtu) { |
276 | ETH1394_PRINT(KERN_INFO, dev->name, |
277 | "Local node constrains MTU to %d\n", max_mtu); |
278 | return -ERANGE; |
279 | } |
280 | |
281 | dev->mtu = new_mtu; |
282 | return 0; |
283 | } |
284 | |
285 | static void purge_partial_datagram(struct list_head *old) |
286 | { |
287 | struct partial_datagram *pd; |
288 | struct list_head *lh, *n; |
289 | struct fragment_info *fi; |
290 | |
291 | pd = list_entry(old, struct partial_datagram, list); |
292 | |
293 | list_for_each_safe(lh, n, &pd->frag_info) { |
294 | fi = list_entry(lh, struct fragment_info, list); |
295 | list_del(lh); |
296 | kfree(fi); |
297 | } |
298 | list_del(old); |
299 | kfree_skb(pd->skb); |
300 | kfree(pd); |
301 | } |
302 | |
303 | /****************************************** |
304 | * 1394 bus activity functions |
305 | ******************************************/ |
306 | |
307 | static struct eth1394_node_ref *eth1394_find_node(struct list_head *inl, |
308 | struct unit_directory *ud) |
309 | { |
310 | struct eth1394_node_ref *node; |
311 | |
312 | list_for_each_entry(node, inl, list) |
313 | if (node->ud == ud) |
314 | return node; |
315 | |
316 | return NULL; |
317 | } |
318 | |
319 | static struct eth1394_node_ref *eth1394_find_node_guid(struct list_head *inl, |
320 | u64 guid) |
321 | { |
322 | struct eth1394_node_ref *node; |
323 | |
324 | list_for_each_entry(node, inl, list) |
325 | if (node->ud->ne->guid == guid) |
326 | return node; |
327 | |
328 | return NULL; |
329 | } |
330 | |
331 | static struct eth1394_node_ref *eth1394_find_node_nodeid(struct list_head *inl, |
332 | nodeid_t nodeid) |
333 | { |
334 | struct eth1394_node_ref *node; |
335 | |
336 | list_for_each_entry(node, inl, list) |
337 | if (node->ud->ne->nodeid == nodeid) |
338 | return node; |
339 | |
340 | return NULL; |
341 | } |
342 | |
343 | static int eth1394_new_node(struct eth1394_host_info *hi, |
344 | struct unit_directory *ud) |
345 | { |
346 | struct eth1394_priv *priv; |
347 | struct eth1394_node_ref *new_node; |
348 | struct eth1394_node_info *node_info; |
349 | |
350 | new_node = kmalloc(sizeof(*new_node), GFP_KERNEL); |
351 | if (!new_node) |
352 | return -ENOMEM; |
353 | |
354 | node_info = kmalloc(sizeof(*node_info), GFP_KERNEL); |
355 | if (!node_info) { |
356 | kfree(new_node); |
357 | return -ENOMEM; |
358 | } |
359 | |
360 | spin_lock_init(&node_info->pdg.lock); |
361 | INIT_LIST_HEAD(&node_info->pdg.list); |
362 | node_info->pdg.sz = 0; |
363 | node_info->fifo = CSR1212_INVALID_ADDR_SPACE; |
364 | |
365 | dev_set_drvdata(&ud->device, node_info); |
366 | new_node->ud = ud; |
367 | |
368 | priv = netdev_priv(hi->dev); |
369 | list_add_tail(&new_node->list, &priv->ip_node_list); |
370 | return 0; |
371 | } |
372 | |
373 | static int eth1394_probe(struct device *dev) |
374 | { |
375 | struct unit_directory *ud; |
376 | struct eth1394_host_info *hi; |
377 | |
378 | ud = container_of(dev, struct unit_directory, device); |
379 | hi = hpsb_get_hostinfo(ð1394_highlevel, ud->ne->host); |
380 | if (!hi) |
381 | return -ENOENT; |
382 | |
383 | return eth1394_new_node(hi, ud); |
384 | } |
385 | |
386 | static int eth1394_remove(struct device *dev) |
387 | { |
388 | struct unit_directory *ud; |
389 | struct eth1394_host_info *hi; |
390 | struct eth1394_priv *priv; |
391 | struct eth1394_node_ref *old_node; |
392 | struct eth1394_node_info *node_info; |
393 | struct list_head *lh, *n; |
394 | unsigned long flags; |
395 | |
396 | ud = container_of(dev, struct unit_directory, device); |
397 | hi = hpsb_get_hostinfo(ð1394_highlevel, ud->ne->host); |
398 | if (!hi) |
399 | return -ENOENT; |
400 | |
401 | priv = netdev_priv(hi->dev); |
402 | |
403 | old_node = eth1394_find_node(&priv->ip_node_list, ud); |
404 | if (!old_node) |
405 | return 0; |
406 | |
407 | list_del(&old_node->list); |
408 | kfree(old_node); |
409 | |
410 | node_info = dev_get_drvdata(&ud->device); |
411 | |
412 | spin_lock_irqsave(&node_info->pdg.lock, flags); |
413 | /* The partial datagram list should be empty, but we'll just |
414 | * make sure anyway... */ |
415 | list_for_each_safe(lh, n, &node_info->pdg.list) |
416 | purge_partial_datagram(lh); |
417 | spin_unlock_irqrestore(&node_info->pdg.lock, flags); |
418 | |
419 | kfree(node_info); |
420 | dev_set_drvdata(&ud->device, NULL); |
421 | return 0; |
422 | } |
423 | |
424 | static int eth1394_update(struct unit_directory *ud) |
425 | { |
426 | struct eth1394_host_info *hi; |
427 | struct eth1394_priv *priv; |
428 | struct eth1394_node_ref *node; |
429 | |
430 | hi = hpsb_get_hostinfo(ð1394_highlevel, ud->ne->host); |
431 | if (!hi) |
432 | return -ENOENT; |
433 | |
434 | priv = netdev_priv(hi->dev); |
435 | node = eth1394_find_node(&priv->ip_node_list, ud); |
436 | if (node) |
437 | return 0; |
438 | |
439 | return eth1394_new_node(hi, ud); |
440 | } |
441 | |
442 | static const struct ieee1394_device_id eth1394_id_table[] = { |
443 | { |
444 | .match_flags = (IEEE1394_MATCH_SPECIFIER_ID | |
445 | IEEE1394_MATCH_VERSION), |
446 | .specifier_id = ETHER1394_GASP_SPECIFIER_ID, |
447 | .version = ETHER1394_GASP_VERSION, |
448 | }, |
449 | {} |
450 | }; |
451 | |
452 | MODULE_DEVICE_TABLE(ieee1394, eth1394_id_table); |
453 | |
454 | static struct hpsb_protocol_driver eth1394_proto_driver = { |
455 | .name = driver_name, |
456 | .id_table = eth1394_id_table, |
457 | .update = eth1394_update, |
458 | .driver = { |
459 | .probe = eth1394_probe, |
460 | .remove = eth1394_remove, |
461 | }, |
462 | }; |
463 | |
464 | static void ether1394_reset_priv(struct net_device *dev, int set_mtu) |
465 | { |
466 | unsigned long flags; |
467 | int i; |
468 | struct eth1394_priv *priv = netdev_priv(dev); |
469 | struct hpsb_host *host = priv->host; |
470 | u64 guid = get_unaligned((u64 *)&(host->csr.rom->bus_info_data[3])); |
471 | int max_speed = IEEE1394_SPEED_MAX; |
472 | |
473 | spin_lock_irqsave(&priv->lock, flags); |
474 | |
475 | memset(priv->ud_list, 0, sizeof(priv->ud_list)); |
476 | priv->bc_maxpayload = 512; |
477 | |
478 | /* Determine speed limit */ |
479 | /* FIXME: This is broken for nodes with link speed < PHY speed, |
480 | * and it is suboptimal for S200B...S800B hardware. |
481 | * The result of nodemgr's speed probe should be used somehow. */ |
482 | for (i = 0; i < host->node_count; i++) { |
483 | /* take care of S100B...S400B PHY ports */ |
484 | if (host->speed[i] == SELFID_SPEED_UNKNOWN) { |
485 | max_speed = IEEE1394_SPEED_100; |
486 | break; |
487 | } |
488 | if (max_speed > host->speed[i]) |
489 | max_speed = host->speed[i]; |
490 | } |
491 | priv->bc_sspd = max_speed; |
492 | |
493 | if (set_mtu) { |
494 | /* Use the RFC 2734 default 1500 octets or the maximum payload |
495 | * as initial MTU */ |
496 | dev->mtu = min(1500, ether1394_max_mtu(host)); |
497 | |
498 | /* Set our hardware address while we're at it */ |
499 | memcpy(dev->dev_addr, &guid, sizeof(u64)); |
500 | memset(dev->broadcast, 0xff, sizeof(u64)); |
501 | } |
502 | |
503 | spin_unlock_irqrestore(&priv->lock, flags); |
504 | } |
505 | |
506 | static const struct header_ops ether1394_header_ops = { |
507 | .create = ether1394_header, |
508 | .rebuild = ether1394_rebuild_header, |
509 | .cache = ether1394_header_cache, |
510 | .cache_update = ether1394_header_cache_update, |
511 | .parse = ether1394_header_parse, |
512 | }; |
513 | |
514 | static const struct net_device_ops ether1394_netdev_ops = { |
515 | .ndo_open = ether1394_open, |
516 | .ndo_stop = ether1394_stop, |
517 | .ndo_start_xmit = ether1394_tx, |
518 | .ndo_tx_timeout = ether1394_tx_timeout, |
519 | .ndo_change_mtu = ether1394_change_mtu, |
520 | }; |
521 | |
522 | static void ether1394_init_dev(struct net_device *dev) |
523 | { |
524 | |
525 | dev->header_ops = ðer1394_header_ops; |
526 | dev->netdev_ops = ðer1394_netdev_ops; |
527 | |
528 | SET_ETHTOOL_OPS(dev, ðtool_ops); |
529 | |
530 | dev->watchdog_timeo = ETHER1394_TIMEOUT; |
531 | dev->flags = IFF_BROADCAST | IFF_MULTICAST; |
532 | dev->features = NETIF_F_HIGHDMA; |
533 | dev->addr_len = ETH1394_ALEN; |
534 | dev->hard_header_len = ETH1394_HLEN; |
535 | dev->type = ARPHRD_IEEE1394; |
536 | |
537 | /* FIXME: This value was copied from ether_setup(). Is it too much? */ |
538 | dev->tx_queue_len = 1000; |
539 | } |
540 | |
541 | /* |
542 | * Wake the queue up after commonly encountered transmit failure conditions are |
543 | * hopefully over. Currently only tlabel exhaustion is accounted for. |
544 | */ |
545 | static void ether1394_wake_queue(struct work_struct *work) |
546 | { |
547 | struct eth1394_priv *priv; |
548 | struct hpsb_packet *packet; |
549 | |
550 | priv = container_of(work, struct eth1394_priv, wake); |
551 | packet = hpsb_alloc_packet(0); |
552 | |
553 | /* This is really bad, but unjam the queue anyway. */ |
554 | if (!packet) |
555 | goto out; |
556 | |
557 | packet->host = priv->host; |
558 | packet->node_id = priv->wake_node; |
559 | /* |
560 | * A transaction label is all we really want. If we get one, it almost |
561 | * always means we can get a lot more because the ieee1394 core recycled |
562 | * a whole batch of tlabels, at last. |
563 | */ |
564 | if (hpsb_get_tlabel(packet) == 0) |
565 | hpsb_free_tlabel(packet); |
566 | |
567 | hpsb_free_packet(packet); |
568 | out: |
569 | netif_wake_queue(priv->wake_dev); |
570 | } |
571 | |
572 | /* |
573 | * This function is called every time a card is found. It is generally called |
574 | * when the module is installed. This is where we add all of our ethernet |
575 | * devices. One for each host. |
576 | */ |
577 | static void ether1394_add_host(struct hpsb_host *host) |
578 | { |
579 | struct eth1394_host_info *hi = NULL; |
580 | struct net_device *dev = NULL; |
581 | struct eth1394_priv *priv; |
582 | u64 fifo_addr; |
583 | |
584 | if (hpsb_config_rom_ip1394_add(host) != 0) { |
585 | ETH1394_PRINT_G(KERN_ERR, "Can't add IP-over-1394 ROM entry\n"); |
586 | return; |
587 | } |
588 | |
589 | fifo_addr = hpsb_allocate_and_register_addrspace( |
590 | ð1394_highlevel, host, &addr_ops, |
591 | ETHER1394_REGION_ADDR_LEN, ETHER1394_REGION_ADDR_LEN, |
592 | CSR1212_INVALID_ADDR_SPACE, CSR1212_INVALID_ADDR_SPACE); |
593 | if (fifo_addr == CSR1212_INVALID_ADDR_SPACE) { |
594 | ETH1394_PRINT_G(KERN_ERR, "Cannot register CSR space\n"); |
595 | hpsb_config_rom_ip1394_remove(host); |
596 | return; |
597 | } |
598 | |
599 | dev = alloc_netdev(sizeof(*priv), "eth%d", ether1394_init_dev); |
600 | if (dev == NULL) { |
601 | ETH1394_PRINT_G(KERN_ERR, "Out of memory\n"); |
602 | goto out; |
603 | } |
604 | |
605 | SET_NETDEV_DEV(dev, &host->device); |
606 | |
607 | priv = netdev_priv(dev); |
608 | INIT_LIST_HEAD(&priv->ip_node_list); |
609 | spin_lock_init(&priv->lock); |
610 | priv->host = host; |
611 | priv->local_fifo = fifo_addr; |
612 | INIT_WORK(&priv->wake, ether1394_wake_queue); |
613 | priv->wake_dev = dev; |
614 | |
615 | hi = hpsb_create_hostinfo(ð1394_highlevel, host, sizeof(*hi)); |
616 | if (hi == NULL) { |
617 | ETH1394_PRINT_G(KERN_ERR, "Out of memory\n"); |
618 | goto out; |
619 | } |
620 | |
621 | ether1394_reset_priv(dev, 1); |
622 | |
623 | if (register_netdev(dev)) { |
624 | ETH1394_PRINT_G(KERN_ERR, "Cannot register the driver\n"); |
625 | goto out; |
626 | } |
627 | |
628 | ETH1394_PRINT(KERN_INFO, dev->name, "IPv4 over IEEE 1394 (fw-host%d)\n", |
629 | host->id); |
630 | |
631 | hi->host = host; |
632 | hi->dev = dev; |
633 | |
634 | /* Ignore validity in hopes that it will be set in the future. It'll |
635 | * be checked when the eth device is opened. */ |
636 | priv->broadcast_channel = host->csr.broadcast_channel & 0x3f; |
637 | |
638 | ether1394_recv_init(priv); |
639 | return; |
640 | out: |
641 | if (dev) |
642 | free_netdev(dev); |
643 | if (hi) |
644 | hpsb_destroy_hostinfo(ð1394_highlevel, host); |
645 | hpsb_unregister_addrspace(ð1394_highlevel, host, fifo_addr); |
646 | hpsb_config_rom_ip1394_remove(host); |
647 | } |
648 | |
649 | /* Remove a card from our list */ |
650 | static void ether1394_remove_host(struct hpsb_host *host) |
651 | { |
652 | struct eth1394_host_info *hi; |
653 | struct eth1394_priv *priv; |
654 | |
655 | hi = hpsb_get_hostinfo(ð1394_highlevel, host); |
656 | if (!hi) |
657 | return; |
658 | priv = netdev_priv(hi->dev); |
659 | hpsb_unregister_addrspace(ð1394_highlevel, host, priv->local_fifo); |
660 | hpsb_config_rom_ip1394_remove(host); |
661 | if (priv->iso) |
662 | hpsb_iso_shutdown(priv->iso); |
663 | unregister_netdev(hi->dev); |
664 | free_netdev(hi->dev); |
665 | } |
666 | |
667 | /* A bus reset happened */ |
668 | static void ether1394_host_reset(struct hpsb_host *host) |
669 | { |
670 | struct eth1394_host_info *hi; |
671 | struct eth1394_priv *priv; |
672 | struct net_device *dev; |
673 | struct list_head *lh, *n; |
674 | struct eth1394_node_ref *node; |
675 | struct eth1394_node_info *node_info; |
676 | unsigned long flags; |
677 | |
678 | hi = hpsb_get_hostinfo(ð1394_highlevel, host); |
679 | |
680 | /* This can happen for hosts that we don't use */ |
681 | if (!hi) |
682 | return; |
683 | |
684 | dev = hi->dev; |
685 | priv = netdev_priv(dev); |
686 | |
687 | /* Reset our private host data, but not our MTU */ |
688 | netif_stop_queue(dev); |
689 | ether1394_reset_priv(dev, 0); |
690 | |
691 | list_for_each_entry(node, &priv->ip_node_list, list) { |
692 | node_info = dev_get_drvdata(&node->ud->device); |
693 | |
694 | spin_lock_irqsave(&node_info->pdg.lock, flags); |
695 | |
696 | list_for_each_safe(lh, n, &node_info->pdg.list) |
697 | purge_partial_datagram(lh); |
698 | |
699 | INIT_LIST_HEAD(&(node_info->pdg.list)); |
700 | node_info->pdg.sz = 0; |
701 | |
702 | spin_unlock_irqrestore(&node_info->pdg.lock, flags); |
703 | } |
704 | |
705 | netif_wake_queue(dev); |
706 | } |
707 | |
708 | /****************************************** |
709 | * HW Header net device functions |
710 | ******************************************/ |
711 | /* These functions have been adapted from net/ethernet/eth.c */ |
712 | |
713 | /* Create a fake MAC header for an arbitrary protocol layer. |
714 | * saddr=NULL means use device source address |
715 | * daddr=NULL means leave destination address (eg unresolved arp). */ |
716 | static int ether1394_header(struct sk_buff *skb, struct net_device *dev, |
717 | unsigned short type, const void *daddr, |
718 | const void *saddr, unsigned len) |
719 | { |
720 | struct eth1394hdr *eth = |
721 | (struct eth1394hdr *)skb_push(skb, ETH1394_HLEN); |
722 | |
723 | eth->h_proto = htons(type); |
724 | |
725 | if (dev->flags & (IFF_LOOPBACK | IFF_NOARP)) { |
726 | memset(eth->h_dest, 0, dev->addr_len); |
727 | return dev->hard_header_len; |
728 | } |
729 | |
730 | if (daddr) { |
731 | memcpy(eth->h_dest, daddr, dev->addr_len); |
732 | return dev->hard_header_len; |
733 | } |
734 | |
735 | return -dev->hard_header_len; |
736 | } |
737 | |
738 | /* Rebuild the faked MAC header. This is called after an ARP |
739 | * (or in future other address resolution) has completed on this |
740 | * sk_buff. We now let ARP fill in the other fields. |
741 | * |
742 | * This routine CANNOT use cached dst->neigh! |
743 | * Really, it is used only when dst->neigh is wrong. |
744 | */ |
745 | static int ether1394_rebuild_header(struct sk_buff *skb) |
746 | { |
747 | struct eth1394hdr *eth = (struct eth1394hdr *)skb->data; |
748 | |
749 | if (eth->h_proto == htons(ETH_P_IP)) |
750 | return arp_find((unsigned char *)ð->h_dest, skb); |
751 | |
752 | ETH1394_PRINT(KERN_DEBUG, skb->dev->name, |
753 | "unable to resolve type %04x addresses\n", |
754 | ntohs(eth->h_proto)); |
755 | return 0; |
756 | } |
757 | |
758 | static int ether1394_header_parse(const struct sk_buff *skb, |
759 | unsigned char *haddr) |
760 | { |
761 | memcpy(haddr, skb->dev->dev_addr, ETH1394_ALEN); |
762 | return ETH1394_ALEN; |
763 | } |
764 | |
765 | static int ether1394_header_cache(const struct neighbour *neigh, |
766 | struct hh_cache *hh) |
767 | { |
768 | __be16 type = hh->hh_type; |
769 | struct net_device *dev = neigh->dev; |
770 | struct eth1394hdr *eth = |
771 | (struct eth1394hdr *)((u8 *)hh->hh_data + 16 - ETH1394_HLEN); |
772 | |
773 | if (type == htons(ETH_P_802_3)) |
774 | return -1; |
775 | |
776 | eth->h_proto = type; |
777 | memcpy(eth->h_dest, neigh->ha, dev->addr_len); |
778 | |
779 | hh->hh_len = ETH1394_HLEN; |
780 | return 0; |
781 | } |
782 | |
783 | /* Called by Address Resolution module to notify changes in address. */ |
784 | static void ether1394_header_cache_update(struct hh_cache *hh, |
785 | const struct net_device *dev, |
786 | const unsigned char * haddr) |
787 | { |
788 | memcpy((u8 *)hh->hh_data + 16 - ETH1394_HLEN, haddr, dev->addr_len); |
789 | } |
790 | |
791 | /****************************************** |
792 | * Datagram reception code |
793 | ******************************************/ |
794 | |
795 | /* Copied from net/ethernet/eth.c */ |
796 | static __be16 ether1394_type_trans(struct sk_buff *skb, struct net_device *dev) |
797 | { |
798 | struct eth1394hdr *eth; |
799 | unsigned char *rawp; |
800 | |
801 | skb_reset_mac_header(skb); |
802 | skb_pull(skb, ETH1394_HLEN); |
803 | eth = eth1394_hdr(skb); |
804 | |
805 | if (*eth->h_dest & 1) { |
806 | if (memcmp(eth->h_dest, dev->broadcast, dev->addr_len) == 0) |
807 | skb->pkt_type = PACKET_BROADCAST; |
808 | #if 0 |
809 | else |
810 | skb->pkt_type = PACKET_MULTICAST; |
811 | #endif |
812 | } else { |
813 | if (memcmp(eth->h_dest, dev->dev_addr, dev->addr_len)) |
814 | skb->pkt_type = PACKET_OTHERHOST; |
815 | } |
816 | |
817 | if (ntohs(eth->h_proto) >= 1536) |
818 | return eth->h_proto; |
819 | |
820 | rawp = skb->data; |
821 | |
822 | if (*(unsigned short *)rawp == 0xFFFF) |
823 | return htons(ETH_P_802_3); |
824 | |
825 | return htons(ETH_P_802_2); |
826 | } |
827 | |
828 | /* Parse an encapsulated IP1394 header into an ethernet frame packet. |
829 | * We also perform ARP translation here, if need be. */ |
830 | static __be16 ether1394_parse_encap(struct sk_buff *skb, struct net_device *dev, |
831 | nodeid_t srcid, nodeid_t destid, |
832 | __be16 ether_type) |
833 | { |
834 | struct eth1394_priv *priv = netdev_priv(dev); |
835 | __be64 dest_hw; |
836 | __be16 ret = 0; |
837 | |
838 | /* Setup our hw addresses. We use these to build the ethernet header. */ |
839 | if (destid == (LOCAL_BUS | ALL_NODES)) |
840 | dest_hw = ~cpu_to_be64(0); /* broadcast */ |
841 | else |
842 | dest_hw = cpu_to_be64((u64)priv->host->csr.guid_hi << 32 | |
843 | priv->host->csr.guid_lo); |
844 | |
845 | /* If this is an ARP packet, convert it. First, we want to make |
846 | * use of some of the fields, since they tell us a little bit |
847 | * about the sending machine. */ |
848 | if (ether_type == htons(ETH_P_ARP)) { |
849 | struct eth1394_arp *arp1394 = (struct eth1394_arp *)skb->data; |
850 | struct arphdr *arp = (struct arphdr *)skb->data; |
851 | unsigned char *arp_ptr = (unsigned char *)(arp + 1); |
852 | u64 fifo_addr = (u64)ntohs(arp1394->fifo_hi) << 32 | |
853 | ntohl(arp1394->fifo_lo); |
854 | u8 max_rec = min(priv->host->csr.max_rec, |
855 | (u8)(arp1394->max_rec)); |
856 | int sspd = arp1394->sspd; |
857 | u16 maxpayload; |
858 | struct eth1394_node_ref *node; |
859 | struct eth1394_node_info *node_info; |
860 | __be64 guid; |
861 | |
862 | /* Sanity check. MacOSX seems to be sending us 131 in this |
863 | * field (atleast on my Panther G5). Not sure why. */ |
864 | if (sspd > 5 || sspd < 0) |
865 | sspd = 0; |
866 | |
867 | maxpayload = min(eth1394_speedto_maxpayload[sspd], |
868 | (u16)(1 << (max_rec + 1))); |
869 | |
870 | guid = get_unaligned(&arp1394->s_uniq_id); |
871 | node = eth1394_find_node_guid(&priv->ip_node_list, |
872 | be64_to_cpu(guid)); |
873 | if (!node) |
874 | return cpu_to_be16(0); |
875 | |
876 | node_info = dev_get_drvdata(&node->ud->device); |
877 | |
878 | /* Update our speed/payload/fifo_offset table */ |
879 | node_info->maxpayload = maxpayload; |
880 | node_info->sspd = sspd; |
881 | node_info->fifo = fifo_addr; |
882 | |
883 | /* Now that we're done with the 1394 specific stuff, we'll |
884 | * need to alter some of the data. Believe it or not, all |
885 | * that needs to be done is sender_IP_address needs to be |
886 | * moved, the destination hardware address get stuffed |
887 | * in and the hardware address length set to 8. |
888 | * |
889 | * IMPORTANT: The code below overwrites 1394 specific data |
890 | * needed above so keep the munging of the data for the |
891 | * higher level IP stack last. */ |
892 | |
893 | arp->ar_hln = 8; |
894 | arp_ptr += arp->ar_hln; /* skip over sender unique id */ |
895 | *(u32 *)arp_ptr = arp1394->sip; /* move sender IP addr */ |
896 | arp_ptr += arp->ar_pln; /* skip over sender IP addr */ |
897 | |
898 | if (arp->ar_op == htons(ARPOP_REQUEST)) |
899 | memset(arp_ptr, 0, sizeof(u64)); |
900 | else |
901 | memcpy(arp_ptr, dev->dev_addr, sizeof(u64)); |
902 | } |
903 | |
904 | /* Now add the ethernet header. */ |
905 | if (dev_hard_header(skb, dev, ntohs(ether_type), &dest_hw, NULL, |
906 | skb->len) >= 0) |
907 | ret = ether1394_type_trans(skb, dev); |
908 | |
909 | return ret; |
910 | } |
911 | |
912 | static int fragment_overlap(struct list_head *frag_list, int offset, int len) |
913 | { |
914 | struct fragment_info *fi; |
915 | int end = offset + len; |
916 | |
917 | list_for_each_entry(fi, frag_list, list) |
918 | if (offset < fi->offset + fi->len && end > fi->offset) |
919 | return 1; |
920 | |
921 | return 0; |
922 | } |
923 | |
924 | static struct list_head *find_partial_datagram(struct list_head *pdgl, int dgl) |
925 | { |
926 | struct partial_datagram *pd; |
927 | |
928 | list_for_each_entry(pd, pdgl, list) |
929 | if (pd->dgl == dgl) |
930 | return &pd->list; |
931 | |
932 | return NULL; |
933 | } |
934 | |
935 | /* Assumes that new fragment does not overlap any existing fragments */ |
936 | static int new_fragment(struct list_head *frag_info, int offset, int len) |
937 | { |
938 | struct list_head *lh; |
939 | struct fragment_info *fi, *fi2, *new; |
940 | |
941 | list_for_each(lh, frag_info) { |
942 | fi = list_entry(lh, struct fragment_info, list); |
943 | if (fi->offset + fi->len == offset) { |
944 | /* The new fragment can be tacked on to the end */ |
945 | fi->len += len; |
946 | /* Did the new fragment plug a hole? */ |
947 | fi2 = list_entry(lh->next, struct fragment_info, list); |
948 | if (fi->offset + fi->len == fi2->offset) { |
949 | /* glue fragments together */ |
950 | fi->len += fi2->len; |
951 | list_del(lh->next); |
952 | kfree(fi2); |
953 | } |
954 | return 0; |
955 | } else if (offset + len == fi->offset) { |
956 | /* The new fragment can be tacked on to the beginning */ |
957 | fi->offset = offset; |
958 | fi->len += len; |
959 | /* Did the new fragment plug a hole? */ |
960 | fi2 = list_entry(lh->prev, struct fragment_info, list); |
961 | if (fi2->offset + fi2->len == fi->offset) { |
962 | /* glue fragments together */ |
963 | fi2->len += fi->len; |
964 | list_del(lh); |
965 | kfree(fi); |
966 | } |
967 | return 0; |
968 | } else if (offset > fi->offset + fi->len) { |
969 | break; |
970 | } else if (offset + len < fi->offset) { |
971 | lh = lh->prev; |
972 | break; |
973 | } |
974 | } |
975 | |
976 | new = kmalloc(sizeof(*new), GFP_ATOMIC); |
977 | if (!new) |
978 | return -ENOMEM; |
979 | |
980 | new->offset = offset; |
981 | new->len = len; |
982 | |
983 | list_add(&new->list, lh); |
984 | return 0; |
985 | } |
986 | |
987 | static int new_partial_datagram(struct net_device *dev, struct list_head *pdgl, |
988 | int dgl, int dg_size, char *frag_buf, |
989 | int frag_off, int frag_len) |
990 | { |
991 | struct partial_datagram *new; |
992 | |
993 | new = kmalloc(sizeof(*new), GFP_ATOMIC); |
994 | if (!new) |
995 | return -ENOMEM; |
996 | |
997 | INIT_LIST_HEAD(&new->frag_info); |
998 | |
999 | if (new_fragment(&new->frag_info, frag_off, frag_len) < 0) { |
1000 | kfree(new); |
1001 | return -ENOMEM; |
1002 | } |
1003 | |
1004 | new->dgl = dgl; |
1005 | new->dg_size = dg_size; |
1006 | |
1007 | new->skb = dev_alloc_skb(dg_size + dev->hard_header_len + 15); |
1008 | if (!new->skb) { |
1009 | struct fragment_info *fi = list_entry(new->frag_info.next, |
1010 | struct fragment_info, |
1011 | list); |
1012 | kfree(fi); |
1013 | kfree(new); |
1014 | return -ENOMEM; |
1015 | } |
1016 | |
1017 | skb_reserve(new->skb, (dev->hard_header_len + 15) & ~15); |
1018 | new->pbuf = skb_put(new->skb, dg_size); |
1019 | memcpy(new->pbuf + frag_off, frag_buf, frag_len); |
1020 | |
1021 | list_add(&new->list, pdgl); |
1022 | return 0; |
1023 | } |
1024 | |
1025 | static int update_partial_datagram(struct list_head *pdgl, struct list_head *lh, |
1026 | char *frag_buf, int frag_off, int frag_len) |
1027 | { |
1028 | struct partial_datagram *pd = |
1029 | list_entry(lh, struct partial_datagram, list); |
1030 | |
1031 | if (new_fragment(&pd->frag_info, frag_off, frag_len) < 0) |
1032 | return -ENOMEM; |
1033 | |
1034 | memcpy(pd->pbuf + frag_off, frag_buf, frag_len); |
1035 | |
1036 | /* Move list entry to beginnig of list so that oldest partial |
1037 | * datagrams percolate to the end of the list */ |
1038 | list_move(lh, pdgl); |
1039 | return 0; |
1040 | } |
1041 | |
1042 | static int is_datagram_complete(struct list_head *lh, int dg_size) |
1043 | { |
1044 | struct partial_datagram *pd; |
1045 | struct fragment_info *fi; |
1046 | |
1047 | pd = list_entry(lh, struct partial_datagram, list); |
1048 | fi = list_entry(pd->frag_info.next, struct fragment_info, list); |
1049 | |
1050 | return (fi->len == dg_size); |
1051 | } |
1052 | |
1053 | /* Packet reception. We convert the IP1394 encapsulation header to an |
1054 | * ethernet header, and fill it with some of our other fields. This is |
1055 | * an incoming packet from the 1394 bus. */ |
1056 | static int ether1394_data_handler(struct net_device *dev, int srcid, int destid, |
1057 | char *buf, int len) |
1058 | { |
1059 | struct sk_buff *skb; |
1060 | unsigned long flags; |
1061 | struct eth1394_priv *priv = netdev_priv(dev); |
1062 | union eth1394_hdr *hdr = (union eth1394_hdr *)buf; |
1063 | __be16 ether_type = cpu_to_be16(0); /* initialized to clear warning */ |
1064 | int hdr_len; |
1065 | struct unit_directory *ud = priv->ud_list[NODEID_TO_NODE(srcid)]; |
1066 | struct eth1394_node_info *node_info; |
1067 | |
1068 | if (!ud) { |
1069 | struct eth1394_node_ref *node; |
1070 | node = eth1394_find_node_nodeid(&priv->ip_node_list, srcid); |
1071 | if (unlikely(!node)) { |
1072 | HPSB_PRINT(KERN_ERR, "ether1394 rx: sender nodeid " |
1073 | "lookup failure: " NODE_BUS_FMT, |
1074 | NODE_BUS_ARGS(priv->host, srcid)); |
1075 | dev->stats.rx_dropped++; |
1076 | return -1; |
1077 | } |
1078 | ud = node->ud; |
1079 | |
1080 | priv->ud_list[NODEID_TO_NODE(srcid)] = ud; |
1081 | } |
1082 | |
1083 | node_info = dev_get_drvdata(&ud->device); |
1084 | |
1085 | /* First, did we receive a fragmented or unfragmented datagram? */ |
1086 | hdr->words.word1 = ntohs(hdr->words.word1); |
1087 | |
1088 | hdr_len = hdr_type_len[hdr->common.lf]; |
1089 | |
1090 | if (hdr->common.lf == ETH1394_HDR_LF_UF) { |
1091 | /* An unfragmented datagram has been received by the ieee1394 |
1092 | * bus. Build an skbuff around it so we can pass it to the |
1093 | * high level network layer. */ |
1094 | |
1095 | skb = dev_alloc_skb(len + dev->hard_header_len + 15); |
1096 | if (unlikely(!skb)) { |
1097 | ETH1394_PRINT_G(KERN_ERR, "Out of memory\n"); |
1098 | dev->stats.rx_dropped++; |
1099 | return -1; |
1100 | } |
1101 | skb_reserve(skb, (dev->hard_header_len + 15) & ~15); |
1102 | memcpy(skb_put(skb, len - hdr_len), buf + hdr_len, |
1103 | len - hdr_len); |
1104 | ether_type = hdr->uf.ether_type; |
1105 | } else { |
1106 | /* A datagram fragment has been received, now the fun begins. */ |
1107 | |
1108 | struct list_head *pdgl, *lh; |
1109 | struct partial_datagram *pd; |
1110 | int fg_off; |
1111 | int fg_len = len - hdr_len; |
1112 | int dg_size; |
1113 | int dgl; |
1114 | int retval; |
1115 | struct pdg_list *pdg = &(node_info->pdg); |
1116 | |
1117 | hdr->words.word3 = ntohs(hdr->words.word3); |
1118 | /* The 4th header word is reserved so no need to do ntohs() */ |
1119 | |
1120 | if (hdr->common.lf == ETH1394_HDR_LF_FF) { |
1121 | ether_type = hdr->ff.ether_type; |
1122 | dgl = hdr->ff.dgl; |
1123 | dg_size = hdr->ff.dg_size + 1; |
1124 | fg_off = 0; |
1125 | } else { |
1126 | hdr->words.word2 = ntohs(hdr->words.word2); |
1127 | dgl = hdr->sf.dgl; |
1128 | dg_size = hdr->sf.dg_size + 1; |
1129 | fg_off = hdr->sf.fg_off; |
1130 | } |
1131 | spin_lock_irqsave(&pdg->lock, flags); |
1132 | |
1133 | pdgl = &(pdg->list); |
1134 | lh = find_partial_datagram(pdgl, dgl); |
1135 | |
1136 | if (lh == NULL) { |
1137 | while (pdg->sz >= max_partial_datagrams) { |
1138 | /* remove the oldest */ |
1139 | purge_partial_datagram(pdgl->prev); |
1140 | pdg->sz--; |
1141 | } |
1142 | |
1143 | retval = new_partial_datagram(dev, pdgl, dgl, dg_size, |
1144 | buf + hdr_len, fg_off, |
1145 | fg_len); |
1146 | if (retval < 0) { |
1147 | spin_unlock_irqrestore(&pdg->lock, flags); |
1148 | goto bad_proto; |
1149 | } |
1150 | pdg->sz++; |
1151 | lh = find_partial_datagram(pdgl, dgl); |
1152 | } else { |
1153 | pd = list_entry(lh, struct partial_datagram, list); |
1154 | |
1155 | if (fragment_overlap(&pd->frag_info, fg_off, fg_len)) { |
1156 | /* Overlapping fragments, obliterate old |
1157 | * datagram and start new one. */ |
1158 | purge_partial_datagram(lh); |
1159 | retval = new_partial_datagram(dev, pdgl, dgl, |
1160 | dg_size, |
1161 | buf + hdr_len, |
1162 | fg_off, fg_len); |
1163 | if (retval < 0) { |
1164 | pdg->sz--; |
1165 | spin_unlock_irqrestore(&pdg->lock, flags); |
1166 | goto bad_proto; |
1167 | } |
1168 | } else { |
1169 | retval = update_partial_datagram(pdgl, lh, |
1170 | buf + hdr_len, |
1171 | fg_off, fg_len); |
1172 | if (retval < 0) { |
1173 | /* Couldn't save off fragment anyway |
1174 | * so might as well obliterate the |
1175 | * datagram now. */ |
1176 | purge_partial_datagram(lh); |
1177 | pdg->sz--; |
1178 | spin_unlock_irqrestore(&pdg->lock, flags); |
1179 | goto bad_proto; |
1180 | } |
1181 | } /* fragment overlap */ |
1182 | } /* new datagram or add to existing one */ |
1183 | |
1184 | pd = list_entry(lh, struct partial_datagram, list); |
1185 | |
1186 | if (hdr->common.lf == ETH1394_HDR_LF_FF) |
1187 | pd->ether_type = ether_type; |
1188 | |
1189 | if (is_datagram_complete(lh, dg_size)) { |
1190 | ether_type = pd->ether_type; |
1191 | pdg->sz--; |
1192 | skb = skb_get(pd->skb); |
1193 | purge_partial_datagram(lh); |
1194 | spin_unlock_irqrestore(&pdg->lock, flags); |
1195 | } else { |
1196 | /* Datagram is not complete, we're done for the |
1197 | * moment. */ |
1198 | spin_unlock_irqrestore(&pdg->lock, flags); |
1199 | return 0; |
1200 | } |
1201 | } /* unframgented datagram or fragmented one */ |
1202 | |
1203 | /* Write metadata, and then pass to the receive level */ |
1204 | skb->dev = dev; |
1205 | skb->ip_summed = CHECKSUM_UNNECESSARY; /* don't check it */ |
1206 | |
1207 | /* Parse the encapsulation header. This actually does the job of |
1208 | * converting to an ethernet frame header, aswell as arp |
1209 | * conversion if needed. ARP conversion is easier in this |
1210 | * direction, since we are using ethernet as our backend. */ |
1211 | skb->protocol = ether1394_parse_encap(skb, dev, srcid, destid, |
1212 | ether_type); |
1213 | |
1214 | spin_lock_irqsave(&priv->lock, flags); |
1215 | |
1216 | if (!skb->protocol) { |
1217 | dev->stats.rx_errors++; |
1218 | dev->stats.rx_dropped++; |
1219 | dev_kfree_skb_any(skb); |
1220 | } else if (netif_rx(skb) == NET_RX_DROP) { |
1221 | dev->stats.rx_errors++; |
1222 | dev->stats.rx_dropped++; |
1223 | } else { |
1224 | dev->stats.rx_packets++; |
1225 | dev->stats.rx_bytes += skb->len; |
1226 | } |
1227 | |
1228 | spin_unlock_irqrestore(&priv->lock, flags); |
1229 | |
1230 | bad_proto: |
1231 | if (netif_queue_stopped(dev)) |
1232 | netif_wake_queue(dev); |
1233 | |
1234 | return 0; |
1235 | } |
1236 | |
1237 | static int ether1394_write(struct hpsb_host *host, int srcid, int destid, |
1238 | quadlet_t *data, u64 addr, size_t len, u16 flags) |
1239 | { |
1240 | struct eth1394_host_info *hi; |
1241 | |
1242 | hi = hpsb_get_hostinfo(ð1394_highlevel, host); |
1243 | if (unlikely(!hi)) { |
1244 | ETH1394_PRINT_G(KERN_ERR, "No net device at fw-host%d\n", |
1245 | host->id); |
1246 | return RCODE_ADDRESS_ERROR; |
1247 | } |
1248 | |
1249 | if (ether1394_data_handler(hi->dev, srcid, destid, (char*)data, len)) |
1250 | return RCODE_ADDRESS_ERROR; |
1251 | else |
1252 | return RCODE_COMPLETE; |
1253 | } |
1254 | |
1255 | static void ether1394_iso(struct hpsb_iso *iso) |
1256 | { |
1257 | __be32 *data; |
1258 | char *buf; |
1259 | struct eth1394_host_info *hi; |
1260 | struct net_device *dev; |
1261 | struct eth1394_priv *priv; |
1262 | unsigned int len; |
1263 | u32 specifier_id; |
1264 | u16 source_id; |
1265 | int i; |
1266 | int nready; |
1267 | |
1268 | hi = hpsb_get_hostinfo(ð1394_highlevel, iso->host); |
1269 | if (unlikely(!hi)) { |
1270 | ETH1394_PRINT_G(KERN_ERR, "No net device at fw-host%d\n", |
1271 | iso->host->id); |
1272 | return; |
1273 | } |
1274 | |
1275 | dev = hi->dev; |
1276 | |
1277 | nready = hpsb_iso_n_ready(iso); |
1278 | for (i = 0; i < nready; i++) { |
1279 | struct hpsb_iso_packet_info *info = |
1280 | &iso->infos[(iso->first_packet + i) % iso->buf_packets]; |
1281 | data = (__be32 *)(iso->data_buf.kvirt + info->offset); |
1282 | |
1283 | /* skip over GASP header */ |
1284 | buf = (char *)data + 8; |
1285 | len = info->len - 8; |
1286 | |
1287 | specifier_id = (be32_to_cpu(data[0]) & 0xffff) << 8 | |
1288 | (be32_to_cpu(data[1]) & 0xff000000) >> 24; |
1289 | source_id = be32_to_cpu(data[0]) >> 16; |
1290 | |
1291 | priv = netdev_priv(dev); |
1292 | |
1293 | if (info->channel != (iso->host->csr.broadcast_channel & 0x3f) |
1294 | || specifier_id != ETHER1394_GASP_SPECIFIER_ID) { |
1295 | /* This packet is not for us */ |
1296 | continue; |
1297 | } |
1298 | ether1394_data_handler(dev, source_id, LOCAL_BUS | ALL_NODES, |
1299 | buf, len); |
1300 | } |
1301 | |
1302 | hpsb_iso_recv_release_packets(iso, i); |
1303 | |
1304 | } |
1305 | |
1306 | /****************************************** |
1307 | * Datagram transmission code |
1308 | ******************************************/ |
1309 | |
1310 | /* Convert a standard ARP packet to 1394 ARP. The first 8 bytes (the entire |
1311 | * arphdr) is the same format as the ip1394 header, so they overlap. The rest |
1312 | * needs to be munged a bit. The remainder of the arphdr is formatted based |
1313 | * on hwaddr len and ipaddr len. We know what they'll be, so it's easy to |
1314 | * judge. |
1315 | * |
1316 | * Now that the EUI is used for the hardware address all we need to do to make |
1317 | * this work for 1394 is to insert 2 quadlets that contain max_rec size, |
1318 | * speed, and unicast FIFO address information between the sender_unique_id |
1319 | * and the IP addresses. |
1320 | */ |
1321 | static void ether1394_arp_to_1394arp(struct sk_buff *skb, |
1322 | struct net_device *dev) |
1323 | { |
1324 | struct eth1394_priv *priv = netdev_priv(dev); |
1325 | struct arphdr *arp = (struct arphdr *)skb->data; |
1326 | unsigned char *arp_ptr = (unsigned char *)(arp + 1); |
1327 | struct eth1394_arp *arp1394 = (struct eth1394_arp *)skb->data; |
1328 | |
1329 | arp1394->hw_addr_len = 16; |
1330 | arp1394->sip = *(u32*)(arp_ptr + ETH1394_ALEN); |
1331 | arp1394->max_rec = priv->host->csr.max_rec; |
1332 | arp1394->sspd = priv->host->csr.lnk_spd; |
1333 | arp1394->fifo_hi = htons(priv->local_fifo >> 32); |
1334 | arp1394->fifo_lo = htonl(priv->local_fifo & ~0x0); |
1335 | } |
1336 | |
1337 | /* We need to encapsulate the standard header with our own. We use the |
1338 | * ethernet header's proto for our own. */ |
1339 | static unsigned int ether1394_encapsulate_prep(unsigned int max_payload, |
1340 | __be16 proto, |
1341 | union eth1394_hdr *hdr, |
1342 | u16 dg_size, u16 dgl) |
1343 | { |
1344 | unsigned int adj_max_payload = |
1345 | max_payload - hdr_type_len[ETH1394_HDR_LF_UF]; |
1346 | |
1347 | /* Does it all fit in one packet? */ |
1348 | if (dg_size <= adj_max_payload) { |
1349 | hdr->uf.lf = ETH1394_HDR_LF_UF; |
1350 | hdr->uf.ether_type = proto; |
1351 | } else { |
1352 | hdr->ff.lf = ETH1394_HDR_LF_FF; |
1353 | hdr->ff.ether_type = proto; |
1354 | hdr->ff.dg_size = dg_size - 1; |
1355 | hdr->ff.dgl = dgl; |
1356 | adj_max_payload = max_payload - hdr_type_len[ETH1394_HDR_LF_FF]; |
1357 | } |
1358 | return DIV_ROUND_UP(dg_size, adj_max_payload); |
1359 | } |
1360 | |
1361 | static unsigned int ether1394_encapsulate(struct sk_buff *skb, |
1362 | unsigned int max_payload, |
1363 | union eth1394_hdr *hdr) |
1364 | { |
1365 | union eth1394_hdr *bufhdr; |
1366 | int ftype = hdr->common.lf; |
1367 | int hdrsz = hdr_type_len[ftype]; |
1368 | unsigned int adj_max_payload = max_payload - hdrsz; |
1369 | |
1370 | switch (ftype) { |
1371 | case ETH1394_HDR_LF_UF: |
1372 | bufhdr = (union eth1394_hdr *)skb_push(skb, hdrsz); |
1373 | bufhdr->words.word1 = htons(hdr->words.word1); |
1374 | bufhdr->words.word2 = hdr->words.word2; |
1375 | break; |
1376 | |
1377 | case ETH1394_HDR_LF_FF: |
1378 | bufhdr = (union eth1394_hdr *)skb_push(skb, hdrsz); |
1379 | bufhdr->words.word1 = htons(hdr->words.word1); |
1380 | bufhdr->words.word2 = hdr->words.word2; |
1381 | bufhdr->words.word3 = htons(hdr->words.word3); |
1382 | bufhdr->words.word4 = 0; |
1383 | |
1384 | /* Set frag type here for future interior fragments */ |
1385 | hdr->common.lf = ETH1394_HDR_LF_IF; |
1386 | hdr->sf.fg_off = 0; |
1387 | break; |
1388 | |
1389 | default: |
1390 | hdr->sf.fg_off += adj_max_payload; |
1391 | bufhdr = (union eth1394_hdr *)skb_pull(skb, adj_max_payload); |
1392 | if (max_payload >= skb->len) |
1393 | hdr->common.lf = ETH1394_HDR_LF_LF; |
1394 | bufhdr->words.word1 = htons(hdr->words.word1); |
1395 | bufhdr->words.word2 = htons(hdr->words.word2); |
1396 | bufhdr->words.word3 = htons(hdr->words.word3); |
1397 | bufhdr->words.word4 = 0; |
1398 | } |
1399 | return min(max_payload, skb->len); |
1400 | } |
1401 | |
1402 | static struct hpsb_packet *ether1394_alloc_common_packet(struct hpsb_host *host) |
1403 | { |
1404 | struct hpsb_packet *p; |
1405 | |
1406 | p = hpsb_alloc_packet(0); |
1407 | if (p) { |
1408 | p->host = host; |
1409 | p->generation = get_hpsb_generation(host); |
1410 | p->type = hpsb_async; |
1411 | } |
1412 | return p; |
1413 | } |
1414 | |
1415 | static int ether1394_prep_write_packet(struct hpsb_packet *p, |
1416 | struct hpsb_host *host, nodeid_t node, |
1417 | u64 addr, void *data, int tx_len) |
1418 | { |
1419 | p->node_id = node; |
1420 | |
1421 | if (hpsb_get_tlabel(p)) |
1422 | return -EAGAIN; |
1423 | |
1424 | p->tcode = TCODE_WRITEB; |
1425 | p->header_size = 16; |
1426 | p->expect_response = 1; |
1427 | p->header[0] = |
1428 | p->node_id << 16 | p->tlabel << 10 | 1 << 8 | TCODE_WRITEB << 4; |
1429 | p->header[1] = host->node_id << 16 | addr >> 32; |
1430 | p->header[2] = addr & 0xffffffff; |
1431 | p->header[3] = tx_len << 16; |
1432 | p->data_size = (tx_len + 3) & ~3; |
1433 | p->data = data; |
1434 | |
1435 | return 0; |
1436 | } |
1437 | |
1438 | static void ether1394_prep_gasp_packet(struct hpsb_packet *p, |
1439 | struct eth1394_priv *priv, |
1440 | struct sk_buff *skb, int length) |
1441 | { |
1442 | p->header_size = 4; |
1443 | p->tcode = TCODE_STREAM_DATA; |
1444 | |
1445 | p->header[0] = length << 16 | 3 << 14 | priv->broadcast_channel << 8 | |
1446 | TCODE_STREAM_DATA << 4; |
1447 | p->data_size = length; |
1448 | p->data = (quadlet_t *)skb->data - 2; |
1449 | p->data[0] = cpu_to_be32(priv->host->node_id << 16 | |
1450 | ETHER1394_GASP_SPECIFIER_ID_HI); |
1451 | p->data[1] = cpu_to_be32(ETHER1394_GASP_SPECIFIER_ID_LO << 24 | |
1452 | ETHER1394_GASP_VERSION); |
1453 | |
1454 | p->speed_code = priv->bc_sspd; |
1455 | |
1456 | /* prevent hpsb_send_packet() from overriding our speed code */ |
1457 | p->node_id = LOCAL_BUS | ALL_NODES; |
1458 | } |
1459 | |
1460 | static void ether1394_free_packet(struct hpsb_packet *packet) |
1461 | { |
1462 | if (packet->tcode != TCODE_STREAM_DATA) |
1463 | hpsb_free_tlabel(packet); |
1464 | hpsb_free_packet(packet); |
1465 | } |
1466 | |
1467 | static void ether1394_complete_cb(void *__ptask); |
1468 | |
1469 | static int ether1394_send_packet(struct packet_task *ptask, unsigned int tx_len) |
1470 | { |
1471 | struct eth1394_priv *priv = ptask->priv; |
1472 | struct hpsb_packet *packet = NULL; |
1473 | |
1474 | packet = ether1394_alloc_common_packet(priv->host); |
1475 | if (!packet) |
1476 | return -ENOMEM; |
1477 | |
1478 | if (ptask->tx_type == ETH1394_GASP) { |
1479 | int length = tx_len + 2 * sizeof(quadlet_t); |
1480 | |
1481 | ether1394_prep_gasp_packet(packet, priv, ptask->skb, length); |
1482 | } else if (ether1394_prep_write_packet(packet, priv->host, |
1483 | ptask->dest_node, |
1484 | ptask->addr, ptask->skb->data, |
1485 | tx_len)) { |
1486 | hpsb_free_packet(packet); |
1487 | return -EAGAIN; |
1488 | } |
1489 | |
1490 | ptask->packet = packet; |
1491 | hpsb_set_packet_complete_task(ptask->packet, ether1394_complete_cb, |
1492 | ptask); |
1493 | |
1494 | if (hpsb_send_packet(packet) < 0) { |
1495 | ether1394_free_packet(packet); |
1496 | return -EIO; |
1497 | } |
1498 | |
1499 | return 0; |
1500 | } |
1501 | |
1502 | /* Task function to be run when a datagram transmission is completed */ |
1503 | static void ether1394_dg_complete(struct packet_task *ptask, int fail) |
1504 | { |
1505 | struct sk_buff *skb = ptask->skb; |
1506 | struct net_device *dev = skb->dev; |
1507 | struct eth1394_priv *priv = netdev_priv(dev); |
1508 | unsigned long flags; |
1509 | |
1510 | /* Statistics */ |
1511 | spin_lock_irqsave(&priv->lock, flags); |
1512 | if (fail) { |
1513 | dev->stats.tx_dropped++; |
1514 | dev->stats.tx_errors++; |
1515 | } else { |
1516 | dev->stats.tx_bytes += skb->len; |
1517 | dev->stats.tx_packets++; |
1518 | } |
1519 | spin_unlock_irqrestore(&priv->lock, flags); |
1520 | |
1521 | dev_kfree_skb_any(skb); |
1522 | kmem_cache_free(packet_task_cache, ptask); |
1523 | } |
1524 | |
1525 | /* Callback for when a packet has been sent and the status of that packet is |
1526 | * known */ |
1527 | static void ether1394_complete_cb(void *__ptask) |
1528 | { |
1529 | struct packet_task *ptask = (struct packet_task *)__ptask; |
1530 | struct hpsb_packet *packet = ptask->packet; |
1531 | int fail = 0; |
1532 | |
1533 | if (packet->tcode != TCODE_STREAM_DATA) |
1534 | fail = hpsb_packet_success(packet); |
1535 | |
1536 | ether1394_free_packet(packet); |
1537 | |
1538 | ptask->outstanding_pkts--; |
1539 | if (ptask->outstanding_pkts > 0 && !fail) { |
1540 | int tx_len, err; |
1541 | |
1542 | /* Add the encapsulation header to the fragment */ |
1543 | tx_len = ether1394_encapsulate(ptask->skb, ptask->max_payload, |
1544 | &ptask->hdr); |
1545 | err = ether1394_send_packet(ptask, tx_len); |
1546 | if (err) { |
1547 | if (err == -EAGAIN) |
1548 | ETH1394_PRINT_G(KERN_ERR, "Out of tlabels\n"); |
1549 | |
1550 | ether1394_dg_complete(ptask, 1); |
1551 | } |
1552 | } else { |
1553 | ether1394_dg_complete(ptask, fail); |
1554 | } |
1555 | } |
1556 | |
1557 | /* Transmit a packet (called by kernel) */ |
1558 | static netdev_tx_t ether1394_tx(struct sk_buff *skb, |
1559 | struct net_device *dev) |
1560 | { |
1561 | struct eth1394hdr hdr_buf; |
1562 | struct eth1394_priv *priv = netdev_priv(dev); |
1563 | __be16 proto; |
1564 | unsigned long flags; |
1565 | nodeid_t dest_node; |
1566 | eth1394_tx_type tx_type; |
1567 | unsigned int tx_len; |
1568 | unsigned int max_payload; |
1569 | u16 dg_size; |
1570 | u16 dgl; |
1571 | struct packet_task *ptask; |
1572 | struct eth1394_node_ref *node; |
1573 | struct eth1394_node_info *node_info = NULL; |
1574 | |
1575 | ptask = kmem_cache_alloc(packet_task_cache, GFP_ATOMIC); |
1576 | if (ptask == NULL) |
1577 | goto fail; |
1578 | |
1579 | /* XXX Ignore this for now. Noticed that when MacOSX is the IRM, |
1580 | * it does not set our validity bit. We need to compensate for |
1581 | * that somewhere else, but not in eth1394. */ |
1582 | #if 0 |
1583 | if ((priv->host->csr.broadcast_channel & 0xc0000000) != 0xc0000000) |
1584 | goto fail; |
1585 | #endif |
1586 | |
1587 | skb = skb_share_check(skb, GFP_ATOMIC); |
1588 | if (!skb) |
1589 | goto fail; |
1590 | |
1591 | /* Get rid of the fake eth1394 header, but first make a copy. |
1592 | * We might need to rebuild the header on tx failure. */ |
1593 | memcpy(&hdr_buf, skb->data, sizeof(hdr_buf)); |
1594 | skb_pull(skb, ETH1394_HLEN); |
1595 | |
1596 | proto = hdr_buf.h_proto; |
1597 | dg_size = skb->len; |
1598 | |
1599 | /* Set the transmission type for the packet. ARP packets and IP |
1600 | * broadcast packets are sent via GASP. */ |
1601 | if (memcmp(hdr_buf.h_dest, dev->broadcast, ETH1394_ALEN) == 0 || |
1602 | proto == htons(ETH_P_ARP) || |
1603 | (proto == htons(ETH_P_IP) && |
1604 | IN_MULTICAST(ntohl(ip_hdr(skb)->daddr)))) { |
1605 | tx_type = ETH1394_GASP; |
1606 | dest_node = LOCAL_BUS | ALL_NODES; |
1607 | max_payload = priv->bc_maxpayload - ETHER1394_GASP_OVERHEAD; |
1608 | BUG_ON(max_payload < 512 - ETHER1394_GASP_OVERHEAD); |
1609 | dgl = priv->bc_dgl; |
1610 | if (max_payload < dg_size + hdr_type_len[ETH1394_HDR_LF_UF]) |
1611 | priv->bc_dgl++; |
1612 | } else { |
1613 | __be64 guid = get_unaligned((__be64 *)hdr_buf.h_dest); |
1614 | |
1615 | node = eth1394_find_node_guid(&priv->ip_node_list, |
1616 | be64_to_cpu(guid)); |
1617 | if (!node) |
1618 | goto fail; |
1619 | |
1620 | node_info = dev_get_drvdata(&node->ud->device); |
1621 | if (node_info->fifo == CSR1212_INVALID_ADDR_SPACE) |
1622 | goto fail; |
1623 | |
1624 | dest_node = node->ud->ne->nodeid; |
1625 | max_payload = node_info->maxpayload; |
1626 | BUG_ON(max_payload < 512 - ETHER1394_GASP_OVERHEAD); |
1627 | |
1628 | dgl = node_info->dgl; |
1629 | if (max_payload < dg_size + hdr_type_len[ETH1394_HDR_LF_UF]) |
1630 | node_info->dgl++; |
1631 | tx_type = ETH1394_WRREQ; |
1632 | } |
1633 | |
1634 | /* If this is an ARP packet, convert it */ |
1635 | if (proto == htons(ETH_P_ARP)) |
1636 | ether1394_arp_to_1394arp(skb, dev); |
1637 | |
1638 | ptask->hdr.words.word1 = 0; |
1639 | ptask->hdr.words.word2 = 0; |
1640 | ptask->hdr.words.word3 = 0; |
1641 | ptask->hdr.words.word4 = 0; |
1642 | ptask->skb = skb; |
1643 | ptask->priv = priv; |
1644 | ptask->tx_type = tx_type; |
1645 | |
1646 | if (tx_type != ETH1394_GASP) { |
1647 | u64 addr; |
1648 | |
1649 | spin_lock_irqsave(&priv->lock, flags); |
1650 | addr = node_info->fifo; |
1651 | spin_unlock_irqrestore(&priv->lock, flags); |
1652 | |
1653 | ptask->addr = addr; |
1654 | ptask->dest_node = dest_node; |
1655 | } |
1656 | |
1657 | ptask->tx_type = tx_type; |
1658 | ptask->max_payload = max_payload; |
1659 | ptask->outstanding_pkts = ether1394_encapsulate_prep(max_payload, |
1660 | proto, &ptask->hdr, dg_size, dgl); |
1661 | |
1662 | /* Add the encapsulation header to the fragment */ |
1663 | tx_len = ether1394_encapsulate(skb, max_payload, &ptask->hdr); |
1664 | dev->trans_start = jiffies; |
1665 | if (ether1394_send_packet(ptask, tx_len)) { |
1666 | if (dest_node == (LOCAL_BUS | ALL_NODES)) |
1667 | goto fail; |
1668 | |
1669 | /* At this point we want to restore the packet. When we return |
1670 | * here with NETDEV_TX_BUSY we will get another entrance in this |
1671 | * routine with the same skb and we need it to look the same. |
1672 | * So we pull 4 more bytes, then build the header again. */ |
1673 | skb_pull(skb, 4); |
1674 | ether1394_header(skb, dev, ntohs(hdr_buf.h_proto), |
1675 | hdr_buf.h_dest, NULL, 0); |
1676 | |
1677 | /* Most failures of ether1394_send_packet are recoverable. */ |
1678 | netif_stop_queue(dev); |
1679 | priv->wake_node = dest_node; |
1680 | schedule_work(&priv->wake); |
1681 | kmem_cache_free(packet_task_cache, ptask); |
1682 | return NETDEV_TX_BUSY; |
1683 | } |
1684 | |
1685 | return NETDEV_TX_OK; |
1686 | fail: |
1687 | if (ptask) |
1688 | kmem_cache_free(packet_task_cache, ptask); |
1689 | |
1690 | if (skb != NULL) |
1691 | dev_kfree_skb(skb); |
1692 | |
1693 | spin_lock_irqsave(&priv->lock, flags); |
1694 | dev->stats.tx_dropped++; |
1695 | dev->stats.tx_errors++; |
1696 | spin_unlock_irqrestore(&priv->lock, flags); |
1697 | |
1698 | return NETDEV_TX_OK; |
1699 | } |
1700 | |
1701 | static void ether1394_get_drvinfo(struct net_device *dev, |
1702 | struct ethtool_drvinfo *info) |
1703 | { |
1704 | strcpy(info->driver, driver_name); |
1705 | strcpy(info->bus_info, "ieee1394"); /* FIXME provide more detail? */ |
1706 | } |
1707 | |
1708 | static const struct ethtool_ops ethtool_ops = { |
1709 | .get_drvinfo = ether1394_get_drvinfo |
1710 | }; |
1711 | |
1712 | static int __init ether1394_init_module(void) |
1713 | { |
1714 | int err; |
1715 | |
1716 | packet_task_cache = kmem_cache_create("packet_task", |
1717 | sizeof(struct packet_task), |
1718 | 0, 0, NULL); |
1719 | if (!packet_task_cache) |
1720 | return -ENOMEM; |
1721 | |
1722 | hpsb_register_highlevel(ð1394_highlevel); |
1723 | err = hpsb_register_protocol(ð1394_proto_driver); |
1724 | if (err) { |
1725 | hpsb_unregister_highlevel(ð1394_highlevel); |
1726 | kmem_cache_destroy(packet_task_cache); |
1727 | } |
1728 | return err; |
1729 | } |
1730 | |
1731 | static void __exit ether1394_exit_module(void) |
1732 | { |
1733 | hpsb_unregister_protocol(ð1394_proto_driver); |
1734 | hpsb_unregister_highlevel(ð1394_highlevel); |
1735 | kmem_cache_destroy(packet_task_cache); |
1736 | } |
1737 | |
1738 | module_init(ether1394_init_module); |
1739 | module_exit(ether1394_exit_module); |
1740 |
Branches:
ben-wpan
ben-wpan-stefan
javiroman/ks7010
jz-2.6.34
jz-2.6.34-rc5
jz-2.6.34-rc6
jz-2.6.34-rc7
jz-2.6.35
jz-2.6.36
jz-2.6.37
jz-2.6.38
jz-2.6.39
jz-3.0
jz-3.1
jz-3.11
jz-3.12
jz-3.13
jz-3.15
jz-3.16
jz-3.18-dt
jz-3.2
jz-3.3
jz-3.4
jz-3.5
jz-3.6
jz-3.6-rc2-pwm
jz-3.9
jz-3.9-clk
jz-3.9-rc8
jz47xx
jz47xx-2.6.38
master
Tags:
od-2011-09-04
od-2011-09-18
v2.6.34-rc5
v2.6.34-rc6
v2.6.34-rc7
v3.9