Root/
1 | /* |
2 | * Copyright (C) 2006 Jim Cromie |
3 | * |
4 | * This is a clocksource driver for the Geode SCx200's 1 or 27 MHz |
5 | * high-resolution timer. The Geode SC-1100 (at least) has a buggy |
6 | * time stamp counter (TSC), which loses time unless 'idle=poll' is |
7 | * given as a boot-arg. In its absence, the Generic Timekeeping code |
8 | * will detect and de-rate the bad TSC, allowing this timer to take |
9 | * over timekeeping duties. |
10 | * |
11 | * Based on work by John Stultz, and Ted Phelps (in a 2.6.12-rc6 patch) |
12 | * |
13 | * This program is free software; you can redistribute it and/or |
14 | * modify it under the terms of the GNU General Public License as |
15 | * published by the Free Software Foundation; either version 2 of the |
16 | * License, or (at your option) any later version. |
17 | */ |
18 | |
19 | #include <linux/clocksource.h> |
20 | #include <linux/init.h> |
21 | #include <linux/module.h> |
22 | #include <linux/ioport.h> |
23 | #include <linux/scx200.h> |
24 | |
25 | #define NAME "scx200_hrt" |
26 | |
27 | static int mhz27; |
28 | module_param(mhz27, int, 0); /* load time only */ |
29 | MODULE_PARM_DESC(mhz27, "count at 27.0 MHz (default is 1.0 MHz)"); |
30 | |
31 | static int ppm; |
32 | module_param(ppm, int, 0); /* load time only */ |
33 | MODULE_PARM_DESC(ppm, "+-adjust to actual XO freq (ppm)"); |
34 | |
35 | /* HiRes Timer configuration register address */ |
36 | #define SCx200_TMCNFG_OFFSET (SCx200_TIMER_OFFSET + 5) |
37 | |
38 | /* and config settings */ |
39 | #define HR_TMEN (1 << 0) /* timer interrupt enable */ |
40 | #define HR_TMCLKSEL (1 << 1) /* 1|0 counts at 27|1 MHz */ |
41 | #define HR_TM27MPD (1 << 2) /* 1 turns off input clock (power-down) */ |
42 | |
43 | /* The base timer frequency, * 27 if selected */ |
44 | #define HRT_FREQ 1000000 |
45 | |
46 | static cycle_t read_hrt(struct clocksource *cs) |
47 | { |
48 | /* Read the timer value */ |
49 | return (cycle_t) inl(scx200_cb_base + SCx200_TIMER_OFFSET); |
50 | } |
51 | |
52 | static struct clocksource cs_hrt = { |
53 | .name = "scx200_hrt", |
54 | .rating = 250, |
55 | .read = read_hrt, |
56 | .mask = CLOCKSOURCE_MASK(32), |
57 | .flags = CLOCK_SOURCE_IS_CONTINUOUS, |
58 | /* mult, shift are set based on mhz27 flag */ |
59 | }; |
60 | |
61 | static int __init init_hrt_clocksource(void) |
62 | { |
63 | u32 freq; |
64 | /* Make sure scx200 has initialized the configuration block */ |
65 | if (!scx200_cb_present()) |
66 | return -ENODEV; |
67 | |
68 | /* Reserve the timer's ISA io-region for ourselves */ |
69 | if (!request_region(scx200_cb_base + SCx200_TIMER_OFFSET, |
70 | SCx200_TIMER_SIZE, |
71 | "NatSemi SCx200 High-Resolution Timer")) { |
72 | pr_warn("unable to lock timer region\n"); |
73 | return -ENODEV; |
74 | } |
75 | |
76 | /* write timer config */ |
77 | outb(HR_TMEN | (mhz27 ? HR_TMCLKSEL : 0), |
78 | scx200_cb_base + SCx200_TMCNFG_OFFSET); |
79 | |
80 | freq = (HRT_FREQ + ppm); |
81 | if (mhz27) |
82 | freq *= 27; |
83 | |
84 | pr_info("enabling scx200 high-res timer (%s MHz +%d ppm)\n", mhz27 ? "27":"1", ppm); |
85 | |
86 | return clocksource_register_hz(&cs_hrt, freq); |
87 | } |
88 | |
89 | module_init(init_hrt_clocksource); |
90 | |
91 | MODULE_AUTHOR("Jim Cromie <jim.cromie@gmail.com>"); |
92 | MODULE_DESCRIPTION("clocksource on SCx200 HiRes Timer"); |
93 | MODULE_LICENSE("GPL"); |
94 |
Branches:
ben-wpan
ben-wpan-stefan
javiroman/ks7010
jz-2.6.34
jz-2.6.34-rc5
jz-2.6.34-rc6
jz-2.6.34-rc7
jz-2.6.35
jz-2.6.36
jz-2.6.37
jz-2.6.38
jz-2.6.39
jz-3.0
jz-3.1
jz-3.11
jz-3.12
jz-3.13
jz-3.15
jz-3.16
jz-3.18-dt
jz-3.2
jz-3.3
jz-3.4
jz-3.5
jz-3.6
jz-3.6-rc2-pwm
jz-3.9
jz-3.9-clk
jz-3.9-rc8
jz47xx
jz47xx-2.6.38
master
Tags:
od-2011-09-04
od-2011-09-18
v2.6.34-rc5
v2.6.34-rc6
v2.6.34-rc7
v3.9