Root/
1 | /* |
2 | * pata_via.c - VIA PATA for new ATA layer |
3 | * (C) 2005-2006 Red Hat Inc |
4 | * |
5 | * Documentation |
6 | * Most chipset documentation available under NDA only |
7 | * |
8 | * VIA version guide |
9 | * VIA VT82C561 - early design, uses ata_generic currently |
10 | * VIA VT82C576 - MWDMA, 33Mhz |
11 | * VIA VT82C586 - MWDMA, 33Mhz |
12 | * VIA VT82C586a - Added UDMA to 33Mhz |
13 | * VIA VT82C586b - UDMA33 |
14 | * VIA VT82C596a - Nonfunctional UDMA66 |
15 | * VIA VT82C596b - Working UDMA66 |
16 | * VIA VT82C686 - Nonfunctional UDMA66 |
17 | * VIA VT82C686a - Working UDMA66 |
18 | * VIA VT82C686b - Updated to UDMA100 |
19 | * VIA VT8231 - UDMA100 |
20 | * VIA VT8233 - UDMA100 |
21 | * VIA VT8233a - UDMA133 |
22 | * VIA VT8233c - UDMA100 |
23 | * VIA VT8235 - UDMA133 |
24 | * VIA VT8237 - UDMA133 |
25 | * VIA VT8237A - UDMA133 |
26 | * VIA VT8237S - UDMA133 |
27 | * VIA VT8251 - UDMA133 |
28 | * |
29 | * Most registers remain compatible across chips. Others start reserved |
30 | * and acquire sensible semantics if set to 1 (eg cable detect). A few |
31 | * exceptions exist, notably around the FIFO settings. |
32 | * |
33 | * One additional quirk of the VIA design is that like ALi they use few |
34 | * PCI IDs for a lot of chips. |
35 | * |
36 | * Based heavily on: |
37 | * |
38 | * Version 3.38 |
39 | * |
40 | * VIA IDE driver for Linux. Supported southbridges: |
41 | * |
42 | * vt82c576, vt82c586, vt82c586a, vt82c586b, vt82c596a, vt82c596b, |
43 | * vt82c686, vt82c686a, vt82c686b, vt8231, vt8233, vt8233c, vt8233a, |
44 | * vt8235, vt8237 |
45 | * |
46 | * Copyright (c) 2000-2002 Vojtech Pavlik |
47 | * |
48 | * Based on the work of: |
49 | * Michel Aubry |
50 | * Jeff Garzik |
51 | * Andre Hedrick |
52 | |
53 | */ |
54 | |
55 | #include <linux/kernel.h> |
56 | #include <linux/module.h> |
57 | #include <linux/pci.h> |
58 | #include <linux/init.h> |
59 | #include <linux/blkdev.h> |
60 | #include <linux/delay.h> |
61 | #include <linux/gfp.h> |
62 | #include <scsi/scsi_host.h> |
63 | #include <linux/libata.h> |
64 | #include <linux/dmi.h> |
65 | |
66 | #define DRV_NAME "pata_via" |
67 | #define DRV_VERSION "0.3.4" |
68 | |
69 | enum { |
70 | VIA_BAD_PREQ = 0x01, /* Crashes if PREQ# till DDACK# set */ |
71 | VIA_BAD_CLK66 = 0x02, /* 66 MHz clock doesn't work correctly */ |
72 | VIA_SET_FIFO = 0x04, /* Needs to have FIFO split set */ |
73 | VIA_NO_UNMASK = 0x08, /* Doesn't work with IRQ unmasking on */ |
74 | VIA_BAD_ID = 0x10, /* Has wrong vendor ID (0x1107) */ |
75 | VIA_BAD_AST = 0x20, /* Don't touch Address Setup Timing */ |
76 | VIA_NO_ENABLES = 0x40, /* Has no enablebits */ |
77 | VIA_SATA_PATA = 0x80, /* SATA/PATA combined configuration */ |
78 | }; |
79 | |
80 | enum { |
81 | VIA_IDFLAG_SINGLE = (1 << 0), /* single channel controller) */ |
82 | }; |
83 | |
84 | /* |
85 | * VIA SouthBridge chips. |
86 | */ |
87 | |
88 | static const struct via_isa_bridge { |
89 | const char *name; |
90 | u16 id; |
91 | u8 rev_min; |
92 | u8 rev_max; |
93 | u8 udma_mask; |
94 | u8 flags; |
95 | } via_isa_bridges[] = { |
96 | { "vx855", PCI_DEVICE_ID_VIA_VX855, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST | VIA_SATA_PATA }, |
97 | { "vx800", PCI_DEVICE_ID_VIA_VX800, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST | VIA_SATA_PATA }, |
98 | { "vt8261", PCI_DEVICE_ID_VIA_8261, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST }, |
99 | { "vt8237s", PCI_DEVICE_ID_VIA_8237S, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST }, |
100 | { "vt8251", PCI_DEVICE_ID_VIA_8251, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST }, |
101 | { "cx700", PCI_DEVICE_ID_VIA_CX700, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST | VIA_SATA_PATA }, |
102 | { "vt6410", PCI_DEVICE_ID_VIA_6410, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST | VIA_NO_ENABLES }, |
103 | { "vt6415", PCI_DEVICE_ID_VIA_6415, 0x00, 0xff, ATA_UDMA6, VIA_BAD_AST | VIA_NO_ENABLES }, |
104 | { "vt8237a", PCI_DEVICE_ID_VIA_8237A, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST }, |
105 | { "vt8237", PCI_DEVICE_ID_VIA_8237, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST }, |
106 | { "vt8235", PCI_DEVICE_ID_VIA_8235, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST }, |
107 | { "vt8233a", PCI_DEVICE_ID_VIA_8233A, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST }, |
108 | { "vt8233c", PCI_DEVICE_ID_VIA_8233C_0, 0x00, 0x2f, ATA_UDMA5, }, |
109 | { "vt8233", PCI_DEVICE_ID_VIA_8233_0, 0x00, 0x2f, ATA_UDMA5, }, |
110 | { "vt8231", PCI_DEVICE_ID_VIA_8231, 0x00, 0x2f, ATA_UDMA5, }, |
111 | { "vt82c686b", PCI_DEVICE_ID_VIA_82C686, 0x40, 0x4f, ATA_UDMA5, }, |
112 | { "vt82c686a", PCI_DEVICE_ID_VIA_82C686, 0x10, 0x2f, ATA_UDMA4, }, |
113 | { "vt82c686", PCI_DEVICE_ID_VIA_82C686, 0x00, 0x0f, ATA_UDMA2, VIA_BAD_CLK66 }, |
114 | { "vt82c596b", PCI_DEVICE_ID_VIA_82C596, 0x10, 0x2f, ATA_UDMA4, }, |
115 | { "vt82c596a", PCI_DEVICE_ID_VIA_82C596, 0x00, 0x0f, ATA_UDMA2, VIA_BAD_CLK66 }, |
116 | { "vt82c586b", PCI_DEVICE_ID_VIA_82C586_0, 0x47, 0x4f, ATA_UDMA2, VIA_SET_FIFO }, |
117 | { "vt82c586b", PCI_DEVICE_ID_VIA_82C586_0, 0x40, 0x46, ATA_UDMA2, VIA_SET_FIFO | VIA_BAD_PREQ }, |
118 | { "vt82c586b", PCI_DEVICE_ID_VIA_82C586_0, 0x30, 0x3f, ATA_UDMA2, VIA_SET_FIFO }, |
119 | { "vt82c586a", PCI_DEVICE_ID_VIA_82C586_0, 0x20, 0x2f, ATA_UDMA2, VIA_SET_FIFO }, |
120 | { "vt82c586", PCI_DEVICE_ID_VIA_82C586_0, 0x00, 0x0f, 0x00, VIA_SET_FIFO }, |
121 | { "vt82c576", PCI_DEVICE_ID_VIA_82C576, 0x00, 0x2f, 0x00, VIA_SET_FIFO | VIA_NO_UNMASK }, |
122 | { "vt82c576", PCI_DEVICE_ID_VIA_82C576, 0x00, 0x2f, 0x00, VIA_SET_FIFO | VIA_NO_UNMASK | VIA_BAD_ID }, |
123 | { "vtxxxx", PCI_DEVICE_ID_VIA_ANON, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST }, |
124 | { NULL } |
125 | }; |
126 | |
127 | static const struct dmi_system_id no_atapi_dma_dmi_table[] = { |
128 | { |
129 | .ident = "AVERATEC 3200", |
130 | .matches = { |
131 | DMI_MATCH(DMI_BOARD_VENDOR, "AVERATEC"), |
132 | DMI_MATCH(DMI_BOARD_NAME, "3200"), |
133 | }, |
134 | }, |
135 | { } |
136 | }; |
137 | |
138 | struct via_port { |
139 | u8 cached_device; |
140 | }; |
141 | |
142 | /* |
143 | * Cable special cases |
144 | */ |
145 | |
146 | static const struct dmi_system_id cable_dmi_table[] = { |
147 | { |
148 | .ident = "Acer Ferrari 3400", |
149 | .matches = { |
150 | DMI_MATCH(DMI_BOARD_VENDOR, "Acer,Inc."), |
151 | DMI_MATCH(DMI_BOARD_NAME, "Ferrari 3400"), |
152 | }, |
153 | }, |
154 | { } |
155 | }; |
156 | |
157 | static int via_cable_override(struct pci_dev *pdev) |
158 | { |
159 | /* Systems by DMI */ |
160 | if (dmi_check_system(cable_dmi_table)) |
161 | return 1; |
162 | /* Arima W730-K8/Targa Visionary 811/... */ |
163 | if (pdev->subsystem_vendor == 0x161F && pdev->subsystem_device == 0x2032) |
164 | return 1; |
165 | return 0; |
166 | } |
167 | |
168 | |
169 | /** |
170 | * via_cable_detect - cable detection |
171 | * @ap: ATA port |
172 | * |
173 | * Perform cable detection. Actually for the VIA case the BIOS |
174 | * already did this for us. We read the values provided by the |
175 | * BIOS. If you are using an 8235 in a non-PC configuration you |
176 | * may need to update this code. |
177 | * |
178 | * Hotplug also impacts on this. |
179 | */ |
180 | |
181 | static int via_cable_detect(struct ata_port *ap) { |
182 | const struct via_isa_bridge *config = ap->host->private_data; |
183 | struct pci_dev *pdev = to_pci_dev(ap->host->dev); |
184 | u32 ata66; |
185 | |
186 | if (via_cable_override(pdev)) |
187 | return ATA_CBL_PATA40_SHORT; |
188 | |
189 | if ((config->flags & VIA_SATA_PATA) && ap->port_no == 0) |
190 | return ATA_CBL_SATA; |
191 | |
192 | /* Early chips are 40 wire */ |
193 | if (config->udma_mask < ATA_UDMA4) |
194 | return ATA_CBL_PATA40; |
195 | /* UDMA 66 chips have only drive side logic */ |
196 | else if (config->udma_mask < ATA_UDMA5) |
197 | return ATA_CBL_PATA_UNK; |
198 | /* UDMA 100 or later */ |
199 | pci_read_config_dword(pdev, 0x50, &ata66); |
200 | /* Check both the drive cable reporting bits, we might not have |
201 | two drives */ |
202 | if (ata66 & (0x10100000 >> (16 * ap->port_no))) |
203 | return ATA_CBL_PATA80; |
204 | /* Check with ACPI so we can spot BIOS reported SATA bridges */ |
205 | if (ata_acpi_init_gtm(ap) && |
206 | ata_acpi_cbl_80wire(ap, ata_acpi_init_gtm(ap))) |
207 | return ATA_CBL_PATA80; |
208 | return ATA_CBL_PATA40; |
209 | } |
210 | |
211 | static int via_pre_reset(struct ata_link *link, unsigned long deadline) |
212 | { |
213 | struct ata_port *ap = link->ap; |
214 | const struct via_isa_bridge *config = ap->host->private_data; |
215 | |
216 | if (!(config->flags & VIA_NO_ENABLES)) { |
217 | static const struct pci_bits via_enable_bits[] = { |
218 | { 0x40, 1, 0x02, 0x02 }, |
219 | { 0x40, 1, 0x01, 0x01 } |
220 | }; |
221 | struct pci_dev *pdev = to_pci_dev(ap->host->dev); |
222 | if (!pci_test_config_bits(pdev, &via_enable_bits[ap->port_no])) |
223 | return -ENOENT; |
224 | } |
225 | |
226 | return ata_sff_prereset(link, deadline); |
227 | } |
228 | |
229 | |
230 | /** |
231 | * via_do_set_mode - set transfer mode data |
232 | * @ap: ATA interface |
233 | * @adev: ATA device |
234 | * @mode: ATA mode being programmed |
235 | * @set_ast: Set to program address setup |
236 | * @udma_type: UDMA mode/format of registers |
237 | * |
238 | * Program the VIA registers for DMA and PIO modes. Uses the ata timing |
239 | * support in order to compute modes. |
240 | * |
241 | * FIXME: Hotplug will require we serialize multiple mode changes |
242 | * on the two channels. |
243 | */ |
244 | |
245 | static void via_do_set_mode(struct ata_port *ap, struct ata_device *adev, |
246 | int mode, int set_ast, int udma_type) |
247 | { |
248 | struct pci_dev *pdev = to_pci_dev(ap->host->dev); |
249 | struct ata_device *peer = ata_dev_pair(adev); |
250 | struct ata_timing t, p; |
251 | static int via_clock = 33333; /* Bus clock in kHZ */ |
252 | unsigned long T = 1000000000 / via_clock; |
253 | unsigned long UT = T; |
254 | int ut; |
255 | int offset = 3 - (2*ap->port_no) - adev->devno; |
256 | |
257 | switch (udma_type) { |
258 | case ATA_UDMA4: |
259 | UT = T / 2; break; |
260 | case ATA_UDMA5: |
261 | UT = T / 3; break; |
262 | case ATA_UDMA6: |
263 | UT = T / 4; break; |
264 | } |
265 | |
266 | /* Calculate the timing values we require */ |
267 | ata_timing_compute(adev, mode, &t, T, UT); |
268 | |
269 | /* We share 8bit timing so we must merge the constraints */ |
270 | if (peer) { |
271 | if (peer->pio_mode) { |
272 | ata_timing_compute(peer, peer->pio_mode, &p, T, UT); |
273 | ata_timing_merge(&p, &t, &t, ATA_TIMING_8BIT); |
274 | } |
275 | } |
276 | |
277 | /* Address setup is programmable but breaks on UDMA133 setups */ |
278 | if (set_ast) { |
279 | u8 setup; /* 2 bits per drive */ |
280 | int shift = 2 * offset; |
281 | |
282 | pci_read_config_byte(pdev, 0x4C, &setup); |
283 | setup &= ~(3 << shift); |
284 | setup |= (clamp_val(t.setup, 1, 4) - 1) << shift; |
285 | pci_write_config_byte(pdev, 0x4C, setup); |
286 | } |
287 | |
288 | /* Load the PIO mode bits */ |
289 | pci_write_config_byte(pdev, 0x4F - ap->port_no, |
290 | ((clamp_val(t.act8b, 1, 16) - 1) << 4) | (clamp_val(t.rec8b, 1, 16) - 1)); |
291 | pci_write_config_byte(pdev, 0x48 + offset, |
292 | ((clamp_val(t.active, 1, 16) - 1) << 4) | (clamp_val(t.recover, 1, 16) - 1)); |
293 | |
294 | /* Load the UDMA bits according to type */ |
295 | switch (udma_type) { |
296 | case ATA_UDMA2: |
297 | default: |
298 | ut = t.udma ? (0xe0 | (clamp_val(t.udma, 2, 5) - 2)) : 0x03; |
299 | break; |
300 | case ATA_UDMA4: |
301 | ut = t.udma ? (0xe8 | (clamp_val(t.udma, 2, 9) - 2)) : 0x0f; |
302 | break; |
303 | case ATA_UDMA5: |
304 | ut = t.udma ? (0xe0 | (clamp_val(t.udma, 2, 9) - 2)) : 0x07; |
305 | break; |
306 | case ATA_UDMA6: |
307 | ut = t.udma ? (0xe0 | (clamp_val(t.udma, 2, 9) - 2)) : 0x07; |
308 | break; |
309 | } |
310 | |
311 | /* Set UDMA unless device is not UDMA capable */ |
312 | if (udma_type) { |
313 | u8 udma_etc; |
314 | |
315 | pci_read_config_byte(pdev, 0x50 + offset, &udma_etc); |
316 | |
317 | /* clear transfer mode bit */ |
318 | udma_etc &= ~0x20; |
319 | |
320 | if (t.udma) { |
321 | /* preserve 80-wire cable detection bit */ |
322 | udma_etc &= 0x10; |
323 | udma_etc |= ut; |
324 | } |
325 | |
326 | pci_write_config_byte(pdev, 0x50 + offset, udma_etc); |
327 | } |
328 | } |
329 | |
330 | static void via_set_piomode(struct ata_port *ap, struct ata_device *adev) |
331 | { |
332 | const struct via_isa_bridge *config = ap->host->private_data; |
333 | int set_ast = (config->flags & VIA_BAD_AST) ? 0 : 1; |
334 | |
335 | via_do_set_mode(ap, adev, adev->pio_mode, set_ast, config->udma_mask); |
336 | } |
337 | |
338 | static void via_set_dmamode(struct ata_port *ap, struct ata_device *adev) |
339 | { |
340 | const struct via_isa_bridge *config = ap->host->private_data; |
341 | int set_ast = (config->flags & VIA_BAD_AST) ? 0 : 1; |
342 | |
343 | via_do_set_mode(ap, adev, adev->dma_mode, set_ast, config->udma_mask); |
344 | } |
345 | |
346 | /** |
347 | * via_mode_filter - filter buggy device/mode pairs |
348 | * @dev: ATA device |
349 | * @mask: Mode bitmask |
350 | * |
351 | * We need to apply some minimal filtering for old controllers and at least |
352 | * one breed of Transcend SSD. Return the updated mask. |
353 | */ |
354 | |
355 | static unsigned long via_mode_filter(struct ata_device *dev, unsigned long mask) |
356 | { |
357 | struct ata_host *host = dev->link->ap->host; |
358 | const struct via_isa_bridge *config = host->private_data; |
359 | unsigned char model_num[ATA_ID_PROD_LEN + 1]; |
360 | |
361 | if (config->id == PCI_DEVICE_ID_VIA_82C586_0) { |
362 | ata_id_c_string(dev->id, model_num, ATA_ID_PROD, sizeof(model_num)); |
363 | if (strcmp(model_num, "TS64GSSD25-M") == 0) { |
364 | ata_dev_warn(dev, |
365 | "disabling UDMA mode due to reported lockups with this device\n"); |
366 | mask &= ~ ATA_MASK_UDMA; |
367 | } |
368 | } |
369 | |
370 | if (dev->class == ATA_DEV_ATAPI && |
371 | dmi_check_system(no_atapi_dma_dmi_table)) { |
372 | ata_dev_warn(dev, "controller locks up on ATAPI DMA, forcing PIO\n"); |
373 | mask &= ATA_MASK_PIO; |
374 | } |
375 | |
376 | return mask; |
377 | } |
378 | |
379 | /** |
380 | * via_tf_load - send taskfile registers to host controller |
381 | * @ap: Port to which output is sent |
382 | * @tf: ATA taskfile register set |
383 | * |
384 | * Outputs ATA taskfile to standard ATA host controller. |
385 | * |
386 | * Note: This is to fix the internal bug of via chipsets, which |
387 | * will reset the device register after changing the IEN bit on |
388 | * ctl register |
389 | */ |
390 | static void via_tf_load(struct ata_port *ap, const struct ata_taskfile *tf) |
391 | { |
392 | struct ata_ioports *ioaddr = &ap->ioaddr; |
393 | struct via_port *vp = ap->private_data; |
394 | unsigned int is_addr = tf->flags & ATA_TFLAG_ISADDR; |
395 | int newctl = 0; |
396 | |
397 | if (tf->ctl != ap->last_ctl) { |
398 | iowrite8(tf->ctl, ioaddr->ctl_addr); |
399 | ap->last_ctl = tf->ctl; |
400 | ata_wait_idle(ap); |
401 | newctl = 1; |
402 | } |
403 | |
404 | if (tf->flags & ATA_TFLAG_DEVICE) { |
405 | iowrite8(tf->device, ioaddr->device_addr); |
406 | vp->cached_device = tf->device; |
407 | } else if (newctl) |
408 | iowrite8(vp->cached_device, ioaddr->device_addr); |
409 | |
410 | if (is_addr && (tf->flags & ATA_TFLAG_LBA48)) { |
411 | WARN_ON_ONCE(!ioaddr->ctl_addr); |
412 | iowrite8(tf->hob_feature, ioaddr->feature_addr); |
413 | iowrite8(tf->hob_nsect, ioaddr->nsect_addr); |
414 | iowrite8(tf->hob_lbal, ioaddr->lbal_addr); |
415 | iowrite8(tf->hob_lbam, ioaddr->lbam_addr); |
416 | iowrite8(tf->hob_lbah, ioaddr->lbah_addr); |
417 | VPRINTK("hob: feat 0x%X nsect 0x%X, lba 0x%X 0x%X 0x%X\n", |
418 | tf->hob_feature, |
419 | tf->hob_nsect, |
420 | tf->hob_lbal, |
421 | tf->hob_lbam, |
422 | tf->hob_lbah); |
423 | } |
424 | |
425 | if (is_addr) { |
426 | iowrite8(tf->feature, ioaddr->feature_addr); |
427 | iowrite8(tf->nsect, ioaddr->nsect_addr); |
428 | iowrite8(tf->lbal, ioaddr->lbal_addr); |
429 | iowrite8(tf->lbam, ioaddr->lbam_addr); |
430 | iowrite8(tf->lbah, ioaddr->lbah_addr); |
431 | VPRINTK("feat 0x%X nsect 0x%X lba 0x%X 0x%X 0x%X\n", |
432 | tf->feature, |
433 | tf->nsect, |
434 | tf->lbal, |
435 | tf->lbam, |
436 | tf->lbah); |
437 | } |
438 | |
439 | ata_wait_idle(ap); |
440 | } |
441 | |
442 | static int via_port_start(struct ata_port *ap) |
443 | { |
444 | struct via_port *vp; |
445 | struct pci_dev *pdev = to_pci_dev(ap->host->dev); |
446 | |
447 | int ret = ata_bmdma_port_start(ap); |
448 | if (ret < 0) |
449 | return ret; |
450 | |
451 | vp = devm_kzalloc(&pdev->dev, sizeof(struct via_port), GFP_KERNEL); |
452 | if (vp == NULL) |
453 | return -ENOMEM; |
454 | ap->private_data = vp; |
455 | return 0; |
456 | } |
457 | |
458 | static struct scsi_host_template via_sht = { |
459 | ATA_BMDMA_SHT(DRV_NAME), |
460 | }; |
461 | |
462 | static struct ata_port_operations via_port_ops = { |
463 | .inherits = &ata_bmdma_port_ops, |
464 | .cable_detect = via_cable_detect, |
465 | .set_piomode = via_set_piomode, |
466 | .set_dmamode = via_set_dmamode, |
467 | .prereset = via_pre_reset, |
468 | .sff_tf_load = via_tf_load, |
469 | .port_start = via_port_start, |
470 | .mode_filter = via_mode_filter, |
471 | }; |
472 | |
473 | static struct ata_port_operations via_port_ops_noirq = { |
474 | .inherits = &via_port_ops, |
475 | .sff_data_xfer = ata_sff_data_xfer_noirq, |
476 | }; |
477 | |
478 | /** |
479 | * via_config_fifo - set up the FIFO |
480 | * @pdev: PCI device |
481 | * @flags: configuration flags |
482 | * |
483 | * Set the FIFO properties for this device if necessary. Used both on |
484 | * set up and on and the resume path |
485 | */ |
486 | |
487 | static void via_config_fifo(struct pci_dev *pdev, unsigned int flags) |
488 | { |
489 | u8 enable; |
490 | |
491 | /* 0x40 low bits indicate enabled channels */ |
492 | pci_read_config_byte(pdev, 0x40 , &enable); |
493 | enable &= 3; |
494 | |
495 | if (flags & VIA_SET_FIFO) { |
496 | static const u8 fifo_setting[4] = {0x00, 0x60, 0x00, 0x20}; |
497 | u8 fifo; |
498 | |
499 | pci_read_config_byte(pdev, 0x43, &fifo); |
500 | |
501 | /* Clear PREQ# until DDACK# for errata */ |
502 | if (flags & VIA_BAD_PREQ) |
503 | fifo &= 0x7F; |
504 | else |
505 | fifo &= 0x9f; |
506 | /* Turn on FIFO for enabled channels */ |
507 | fifo |= fifo_setting[enable]; |
508 | pci_write_config_byte(pdev, 0x43, fifo); |
509 | } |
510 | } |
511 | |
512 | static void via_fixup(struct pci_dev *pdev, const struct via_isa_bridge *config) |
513 | { |
514 | u32 timing; |
515 | |
516 | /* Initialise the FIFO for the enabled channels. */ |
517 | via_config_fifo(pdev, config->flags); |
518 | |
519 | if (config->udma_mask == ATA_UDMA4) { |
520 | /* The 66 MHz devices require we enable the clock */ |
521 | pci_read_config_dword(pdev, 0x50, &timing); |
522 | timing |= 0x80008; |
523 | pci_write_config_dword(pdev, 0x50, timing); |
524 | } |
525 | if (config->flags & VIA_BAD_CLK66) { |
526 | /* Disable the 66MHz clock on problem devices */ |
527 | pci_read_config_dword(pdev, 0x50, &timing); |
528 | timing &= ~0x80008; |
529 | pci_write_config_dword(pdev, 0x50, timing); |
530 | } |
531 | } |
532 | |
533 | /** |
534 | * via_init_one - discovery callback |
535 | * @pdev: PCI device |
536 | * @id: PCI table info |
537 | * |
538 | * A VIA IDE interface has been discovered. Figure out what revision |
539 | * and perform configuration work before handing it to the ATA layer |
540 | */ |
541 | |
542 | static int via_init_one(struct pci_dev *pdev, const struct pci_device_id *id) |
543 | { |
544 | /* Early VIA without UDMA support */ |
545 | static const struct ata_port_info via_mwdma_info = { |
546 | .flags = ATA_FLAG_SLAVE_POSS, |
547 | .pio_mask = ATA_PIO4, |
548 | .mwdma_mask = ATA_MWDMA2, |
549 | .port_ops = &via_port_ops |
550 | }; |
551 | /* Ditto with IRQ masking required */ |
552 | static const struct ata_port_info via_mwdma_info_borked = { |
553 | .flags = ATA_FLAG_SLAVE_POSS, |
554 | .pio_mask = ATA_PIO4, |
555 | .mwdma_mask = ATA_MWDMA2, |
556 | .port_ops = &via_port_ops_noirq, |
557 | }; |
558 | /* VIA UDMA 33 devices (and borked 66) */ |
559 | static const struct ata_port_info via_udma33_info = { |
560 | .flags = ATA_FLAG_SLAVE_POSS, |
561 | .pio_mask = ATA_PIO4, |
562 | .mwdma_mask = ATA_MWDMA2, |
563 | .udma_mask = ATA_UDMA2, |
564 | .port_ops = &via_port_ops |
565 | }; |
566 | /* VIA UDMA 66 devices */ |
567 | static const struct ata_port_info via_udma66_info = { |
568 | .flags = ATA_FLAG_SLAVE_POSS, |
569 | .pio_mask = ATA_PIO4, |
570 | .mwdma_mask = ATA_MWDMA2, |
571 | .udma_mask = ATA_UDMA4, |
572 | .port_ops = &via_port_ops |
573 | }; |
574 | /* VIA UDMA 100 devices */ |
575 | static const struct ata_port_info via_udma100_info = { |
576 | .flags = ATA_FLAG_SLAVE_POSS, |
577 | .pio_mask = ATA_PIO4, |
578 | .mwdma_mask = ATA_MWDMA2, |
579 | .udma_mask = ATA_UDMA5, |
580 | .port_ops = &via_port_ops |
581 | }; |
582 | /* UDMA133 with bad AST (All current 133) */ |
583 | static const struct ata_port_info via_udma133_info = { |
584 | .flags = ATA_FLAG_SLAVE_POSS, |
585 | .pio_mask = ATA_PIO4, |
586 | .mwdma_mask = ATA_MWDMA2, |
587 | .udma_mask = ATA_UDMA6, /* FIXME: should check north bridge */ |
588 | .port_ops = &via_port_ops |
589 | }; |
590 | const struct ata_port_info *ppi[] = { NULL, NULL }; |
591 | struct pci_dev *isa; |
592 | const struct via_isa_bridge *config; |
593 | u8 enable; |
594 | unsigned long flags = id->driver_data; |
595 | int rc; |
596 | |
597 | ata_print_version_once(&pdev->dev, DRV_VERSION); |
598 | |
599 | rc = pcim_enable_device(pdev); |
600 | if (rc) |
601 | return rc; |
602 | |
603 | if (flags & VIA_IDFLAG_SINGLE) |
604 | ppi[1] = &ata_dummy_port_info; |
605 | |
606 | /* To find out how the IDE will behave and what features we |
607 | actually have to look at the bridge not the IDE controller */ |
608 | for (config = via_isa_bridges; config->id != PCI_DEVICE_ID_VIA_ANON; |
609 | config++) |
610 | if ((isa = pci_get_device(PCI_VENDOR_ID_VIA + |
611 | !!(config->flags & VIA_BAD_ID), |
612 | config->id, NULL))) { |
613 | u8 rev = isa->revision; |
614 | pci_dev_put(isa); |
615 | |
616 | if ((id->device == 0x0415 || id->device == 0x3164) && |
617 | (config->id != id->device)) |
618 | continue; |
619 | |
620 | if (rev >= config->rev_min && rev <= config->rev_max) |
621 | break; |
622 | } |
623 | |
624 | if (!(config->flags & VIA_NO_ENABLES)) { |
625 | /* 0x40 low bits indicate enabled channels */ |
626 | pci_read_config_byte(pdev, 0x40 , &enable); |
627 | enable &= 3; |
628 | if (enable == 0) |
629 | return -ENODEV; |
630 | } |
631 | |
632 | /* Clock set up */ |
633 | switch (config->udma_mask) { |
634 | case 0x00: |
635 | if (config->flags & VIA_NO_UNMASK) |
636 | ppi[0] = &via_mwdma_info_borked; |
637 | else |
638 | ppi[0] = &via_mwdma_info; |
639 | break; |
640 | case ATA_UDMA2: |
641 | ppi[0] = &via_udma33_info; |
642 | break; |
643 | case ATA_UDMA4: |
644 | ppi[0] = &via_udma66_info; |
645 | break; |
646 | case ATA_UDMA5: |
647 | ppi[0] = &via_udma100_info; |
648 | break; |
649 | case ATA_UDMA6: |
650 | ppi[0] = &via_udma133_info; |
651 | break; |
652 | default: |
653 | WARN_ON(1); |
654 | return -ENODEV; |
655 | } |
656 | |
657 | via_fixup(pdev, config); |
658 | |
659 | /* We have established the device type, now fire it up */ |
660 | return ata_pci_bmdma_init_one(pdev, ppi, &via_sht, (void *)config, 0); |
661 | } |
662 | |
663 | #ifdef CONFIG_PM |
664 | /** |
665 | * via_reinit_one - reinit after resume |
666 | * @pdev; PCI device |
667 | * |
668 | * Called when the VIA PATA device is resumed. We must then |
669 | * reconfigure the fifo and other setup we may have altered. In |
670 | * addition the kernel needs to have the resume methods on PCI |
671 | * quirk supported. |
672 | */ |
673 | |
674 | static int via_reinit_one(struct pci_dev *pdev) |
675 | { |
676 | struct ata_host *host = dev_get_drvdata(&pdev->dev); |
677 | int rc; |
678 | |
679 | rc = ata_pci_device_do_resume(pdev); |
680 | if (rc) |
681 | return rc; |
682 | |
683 | via_fixup(pdev, host->private_data); |
684 | |
685 | ata_host_resume(host); |
686 | return 0; |
687 | } |
688 | #endif |
689 | |
690 | static const struct pci_device_id via[] = { |
691 | { PCI_VDEVICE(VIA, 0x0415), }, |
692 | { PCI_VDEVICE(VIA, 0x0571), }, |
693 | { PCI_VDEVICE(VIA, 0x0581), }, |
694 | { PCI_VDEVICE(VIA, 0x1571), }, |
695 | { PCI_VDEVICE(VIA, 0x3164), }, |
696 | { PCI_VDEVICE(VIA, 0x5324), }, |
697 | { PCI_VDEVICE(VIA, 0xC409), VIA_IDFLAG_SINGLE }, |
698 | { PCI_VDEVICE(VIA, 0x9001), VIA_IDFLAG_SINGLE }, |
699 | |
700 | { }, |
701 | }; |
702 | |
703 | static struct pci_driver via_pci_driver = { |
704 | .name = DRV_NAME, |
705 | .id_table = via, |
706 | .probe = via_init_one, |
707 | .remove = ata_pci_remove_one, |
708 | #ifdef CONFIG_PM |
709 | .suspend = ata_pci_device_suspend, |
710 | .resume = via_reinit_one, |
711 | #endif |
712 | }; |
713 | |
714 | module_pci_driver(via_pci_driver); |
715 | |
716 | MODULE_AUTHOR("Alan Cox"); |
717 | MODULE_DESCRIPTION("low-level driver for VIA PATA"); |
718 | MODULE_LICENSE("GPL"); |
719 | MODULE_DEVICE_TABLE(pci, via); |
720 | MODULE_VERSION(DRV_VERSION); |
721 |
Branches:
ben-wpan
ben-wpan-stefan
javiroman/ks7010
jz-2.6.34
jz-2.6.34-rc5
jz-2.6.34-rc6
jz-2.6.34-rc7
jz-2.6.35
jz-2.6.36
jz-2.6.37
jz-2.6.38
jz-2.6.39
jz-3.0
jz-3.1
jz-3.11
jz-3.12
jz-3.13
jz-3.15
jz-3.16
jz-3.18-dt
jz-3.2
jz-3.3
jz-3.4
jz-3.5
jz-3.6
jz-3.6-rc2-pwm
jz-3.9
jz-3.9-clk
jz-3.9-rc8
jz47xx
jz47xx-2.6.38
master
Tags:
od-2011-09-04
od-2011-09-18
v2.6.34-rc5
v2.6.34-rc6
v2.6.34-rc7
v3.9