Root/
1 | IBM ServeRAID driver Change Log |
2 | ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ |
3 | |
4 | 5.00.01 - Sarasota ( 5i ) adapters must always be scanned first |
5 | - Get rid on IOCTL_NEW_COMMAND code |
6 | - Add Extended DCDB Commands for Tape Support in 5I |
7 | |
8 | 4.90.11 - Don't actually RESET unless it's physically required |
9 | - Remove unused compile options |
10 | |
11 | 4.90.08 - Data Corruption if First Scatter Gather Element is > 64K |
12 | |
13 | 4.90.08 - Increase Delays in Flashing ( Trombone Only - 4H ) |
14 | |
15 | 4.90.05 - Use New PCI Architecture to facilitate Hot Plug Development |
16 | |
17 | 4.90.01 - Add ServeRAID Version Checking |
18 | |
19 | 4.80.26 - Clean up potential code problems ( Arjan's recommendations ) |
20 | |
21 | 4.80.21 - Change memcpy() to copy_to_user() in NVRAM Page 5 IOCTL path |
22 | |
23 | 4.80.20 - Set max_sectors in Scsi_Host structure ( if >= 2.4.7 kernel ) |
24 | - 5 second delay needed after resetting an i960 adapter |
25 | |
26 | 4.80.14 - Take all semaphores off stack |
27 | - Clean Up New_IOCTL path |
28 | |
29 | 4.80.04 - Eliminate calls to strtok() if 2.4.x or greater |
30 | - Adjustments to Device Queue Depth |
31 | |
32 | 4.80.00 - Make ia64 Safe |
33 | |
34 | 4.72.01 - I/O Mapped Memory release ( so "insmod ips" does not Fail ) |
35 | - Don't Issue Internal FFDC Command if there are Active Commands |
36 | - Close Window for getting too many IOCTL's active |
37 | |
38 | 4.72.00 - Allow for a Scatter-Gather Element to exceed MAX_XFER Size |
39 | |
40 | 4.71.00 - Change all memory allocations to not use GFP_DMA flag |
41 | - Code Clean-Up for 2.4.x kernel |
42 | |
43 | 4.70.15 - Fix Breakup for very large ( non-SG ) requests |
44 | |
45 | 4.70.13 - Don't release HA Lock in ips_next() until SC taken off queue |
46 | - Unregister SCSI device in ips_release() |
47 | - Don't Send CDB's if we already know the device is not present |
48 | |
49 | 4.70.12 - Corrective actions for bad controller ( during initialization ) |
50 | |
51 | 4.70.09 - Use a Common ( Large Buffer ) for Flashing from the JCRM CD |
52 | - Add IPSSEND Flash Support |
53 | - Set Sense Data for Unknown SCSI Command |
54 | - Use Slot Number from NVRAM Page 5 |
55 | - Restore caller's DCDB Structure |
56 | |
57 | 4.20.14 - Update patch files for kernel 2.4.0-test5 |
58 | |
59 | 4.20.13 - Fix some failure cases / reset code |
60 | - Hook into the reboot_notifier to flush the controller |
61 | cache |
62 | |
63 | 4.20.03 - Rename version to coincide with new release schedules |
64 | - Performance fixes |
65 | - Fix truncation of /proc files with cat |
66 | - Merge in changes through kernel 2.4.0test1ac21 |
67 | |
68 | 4.10.13 - Fix for dynamic unload and proc file system |
69 | |
70 | 4.10.00 - Add support for ServeRAID 4M/4L |
71 | |
72 | 4.00.06 - Fix timeout with initial FFDC command |
73 | |
74 | 4.00.05 - Remove wish_block from init routine |
75 | - Use linux/spinlock.h instead of asm/spinlock.h for kernels |
76 | 2.3.18 and later |
77 | - Sync with other changes from the 2.3 kernels |
78 | |
79 | 4.00.04 - Rename structures/constants to be prefixed with IPS_ |
80 | |
81 | 4.00.03 - Add alternative passthru interface |
82 | - Add ability to flash ServeRAID BIOS |
83 | |
84 | 4.00.02 - Fix problem with PT DCDB with no buffer |
85 | |
86 | 4.00.01 - Add support for First Failure Data Capture |
87 | |
88 | 4.00.00 - Add support for ServeRAID 4 |
89 | |
90 | 3.60.02 - Make DCDB direction based on lookup table. |
91 | - Only allow one DCDB command to a SCSI ID at a time. |
92 | |
93 | 3.60.01 - Remove bogus error check in passthru routine. |
94 | |
95 | 3.60.00 - Bump max commands to 128 for use with ServeRAID |
96 | firmware 3.60. |
97 | - Change version to 3.60 to coincide with ServeRAID release |
98 | numbering. |
99 | |
100 | 1.00.00 - Initial Public Release |
101 | - Functionally equivalent to 0.99.05 |
102 | |
103 | 0.99.05 - Fix an oops on certain passthru commands |
104 | |
105 | 0.99.04 - Fix race condition in the passthru mechanism |
106 | -- this required the interface to the utilities to change |
107 | - Fix error recovery code |
108 | |
109 | 0.99.03 - Make interrupt routine handle all completed request on the |
110 | adapter not just the first one |
111 | - Make sure passthru commands get woken up if we run out of |
112 | SCBs |
113 | - Send all of the commands on the queue at once rather than |
114 | one at a time since the card will support it. |
115 | |
116 | 0.99.02 - Added some additional debug statements to print out |
117 | errors if an error occurs while trying to read/write |
118 | to a logical drive (IPS_DEBUG). |
119 | |
120 | - Fixed read/write errors when the adapter is using an |
121 | 8K stripe size. |
122 | |
123 |
Branches:
ben-wpan
ben-wpan-stefan
javiroman/ks7010
jz-2.6.34
jz-2.6.34-rc5
jz-2.6.34-rc6
jz-2.6.34-rc7
jz-2.6.35
jz-2.6.36
jz-2.6.37
jz-2.6.38
jz-2.6.39
jz-3.0
jz-3.1
jz-3.11
jz-3.12
jz-3.13
jz-3.15
jz-3.16
jz-3.18-dt
jz-3.2
jz-3.3
jz-3.4
jz-3.5
jz-3.6
jz-3.6-rc2-pwm
jz-3.9
jz-3.9-clk
jz-3.9-rc8
jz47xx
jz47xx-2.6.38
master
Tags:
od-2011-09-04
od-2011-09-18
v2.6.34-rc5
v2.6.34-rc6
v2.6.34-rc7
v3.9