| atusb
| USB
| RF
| All sheets
|
 | |
|
>>> Werner Almesberger <werner@almesberger.net>
Tue May 29 02:48:31 2012 -0300
atben/atben.sch, atusb/atrf.sch: correct and clarify ESR of X1 (reported by Wolfgang Spraul)
|
|
| |
>>> Werner Almesberger <werner@almesberger.net>
Wed May 23 23:49:31 2012 -0300
atusb/usb.sch: bring back USB_A_PLUG (was lost for an unknown reason)
|
| |
|
>>> Werner Almesberger <werner@almesberger.net>
Fri May 27 04:29:01 2011 -0300
atusb/: swapped C10 and C13 in schematics, to match layout
|
|
| |
>>> Werner Almesberger <werner@almesberger.net>
Thu May 19 14:23:33 2011 -0300
atusb: varistor Vdc was off by 100 mV; made it clearer that we use Vdc, not Vb
|
|
|
|
>>> Werner Almesberger <werner@openmoko.org>
Mon Feb 14 01:55:46 2011 -0300
atusb: slightly adjusted some component values for easier sourcing
|
|
| |
>>> Werner Almesberger <werner@openmoko.org>
Tue Feb 1 05:01:27 2011 -0300
atmega8u2.lib (PB2): end list of pin names with a slash if wrapped
|
|
| |
>>> Werner Almesberger <werner@openmoko.org>
Mon Jan 31 11:52:30 2011 -0300
usb.sch: cleanup and track layout
|
|
| |
>>> Werner Almesberger <werner@openmoko.org>
Mon Jan 31 05:08:36 2011 -0300
usb.sch: corrected symbol name
|
|
| |
>>> Werner Almesberger <werner@openmoko.org>
Mon Jan 31 04:57:02 2011 -0300
atusb: new layout for the ATmega32U2
|
|
| |
>>> Werner Almesberger <werner@openmoko.org>
Fri Jan 28 03:54:38 2011 -0300
atusb: cleaned up USB schematics
|
|
|
|
>>> Werner Almesberger <werner@openmoko.org>
Fri Jan 28 03:42:35 2011 -0300
atusb: replaced the C8051F326 with an ATmega32U2 (still needs cleanup)
|
| |
|
>>> Werner Almesberger <werner@openmoko.org>
Sat Jan 22 13:22:58 2011 -0300
atusb: introduced optional antenna matching capacitor
|
|
|
|
>>> Werner Almesberger <werner@openmoko.org>
Tue Jan 4 01:19:54 2011 -0300
atusb: switched from the AT86RF230 to the AT86RF231, added missing RF ground
|
| |
|
>>> Werner Almesberger <werner@openmoko.org>
Mon Jan 3 17:21:20 2011 -0300
atusb/atrf.sch: changed C3, C8, C9 to "22pF/RF", to make BOOM select UHI Q type
|
|
| |
>>> Werner Almesberger <werner@openmoko.org>
Mon Jan 3 16:32:52 2011 -0300
atusb/usb.sch: specified capacitance of TVSs (33 pF) and explained why
|
|
| |
>>> Werner Almesberger <werner@openmoko.org>
Mon Jan 3 15:54:35 2011 -0300
atusb/usb.sch: typo: the LED is called LTST-C190KRKT, not LTST-C190KTKR
|
|
| |
>>> Werner Almesberger <werner@openmoko.org>
Fri Dec 17 23:04:37 2010 -0300
usb.sch: explain how the the ID pin works
|
|
|
|
>>> Werner Almesberger <werner@openmoko.org>
Thu Dec 2 23:56:03 2010 -0300
atusb: add automatic board revision detection; clean up feed line
|
|
| |
>>> Werner Almesberger <werner@openmoko.org>
Thu Dec 2 12:16:49 2010 -0300
atusb: rearrange I/Os for new layout
|
|
|
|
>>> Werner Almesberger <werner@openmoko.org>
Wed Dec 1 13:28:05 2010 -0300
atusb: remove two unnecessary test points
|
|
|
|
>>> Werner Almesberger <werner@openmoko.org>
Tue Nov 30 06:39:48 2010 -0300
atusb: use 0402 as the preferred component size and replace bad TVS
|
| |
|
>>> Werner Almesberger <werner@openmoko.org>
Tue Nov 30 05:36:02 2010 -0300
atusb: since we always drive TST, we don't need the pull-down
|
| |
|
>>> Werner Almesberger <werner@openmoko.org>
Tue Nov 30 05:25:58 2010 -0300
atusb: use Johanson 2450FB15L0001 instead of discrete balun circuit
|
|
| |
>>> Werner Almesberger <werner@openmoko.org>
Tue Nov 30 04:56:31 2010 -0300
atusb: switch from mini-USB receptacle to full-size USB plug
|
|
| |
>>> Werner Almesberger <werner@openmoko.org>
Tue Nov 30 04:45:54 2010 -0300
atusb: shrink C2 pads to test point size
|
| | |
>>> Werner Almesberger <werner@openmoko.org>
Tue Nov 30 04:30:04 2010 -0300
atusb: remove test points from MCU-RF interconnect
|
| | |
>>> Werner Almesberger <werner@openmoko.org>
Thu Nov 11 10:36:57 2010 -0300
atusb.sch: mention that the TST connection is a rework and not in the layout
|
|
|
|
>>> Werner Almesberger <werner@openmoko.org>
Thu Nov 11 02:12:45 2010 -0300
atusb/: connect TST to P0_7 (rework of existing boards)
|
| |
|
>>> Werner Almesberger <werner@openmoko.org>
Mon Oct 25 00:53:35 2010 -0300
atusb/atrf.sch (X1): don't explicitly say that the tolerance is a maximum
|
|
|
|
>>> Werner Almesberger <werner@openmoko.org>
Mon Oct 25 00:26:27 2010 -0300
Cleanup of values in atusb/*.sch
|
| |
|
>>> Werner Almesberger <werner@openmoko.org>
Thu Aug 26 00:30:41 2010 -0300
Populated load capacitors of the crystal. Started organizing issues in ECNs.
|
|
| |
>>> Werner Almesberger <werner@openmoko.org>
Fri Aug 20 17:30:19 2010 -0300
Active-high IRQ_RF was routed to active-low interrupt input
|
| |
|
>>> Werner Almesberger <werner@openmoko.org>
Wed Aug 18 17:21:47 2010 -0300
Net name correction, layout update.
|
|
| |
>>> Werner Almesberger <werner@openmoko.org>
Wed Aug 18 15:45:26 2010 -0300
Brown paper bag time: the VDD net was connected to VBUS, not VDD/VIO.
|
| |
|
>>> Werner Almesberger <werner@openmoko.org>
Thu Aug 12 22:35:54 2010 -0300
First layout draft. (No GND areas, not quite following design rules.)
|
|
| |
>>> Werner Almesberger <werner@openmoko.org>
Thu Aug 12 16:02:14 2010 -0300
usb.sch cleanup.
|
|
| |
>>> Werner Almesberger <werner@openmoko.org>
Thu Aug 12 15:50:38 2010 -0300
Updated the LED.
|
|
| |
>>> Werner Almesberger <werner@openmoko.org>
Thu Aug 12 15:35:32 2010 -0300
Added default footprints to schematics.
|
|
|
|
>>> Werner Almesberger <werner@openmoko.org>
Thu Aug 12 13:09:36 2010 -0300
Made first draft of schematics.
|
| |
|
>>> Werner Almesberger <werner@openmoko.org>
Thu Aug 12 10:59:50 2010 -0300
Copied antenna symbol from gta02-core. Updated footprint, and added new items to schematics.
|
|
|
|
>>> Werner Almesberger <werner@openmoko.org>
Tue Aug 10 07:00:22 2010 -0300
Oops, forgot to commit wpan-atrf.pro
|
|
|
|
|